Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The remote requires two AAA batteries (supplied), and the keyboard requires two AA batteries (supplied). Alkaline batteries are recommended. To install the batteries for your remote 1. On the back of the remote, remove the battery cover by loosening the small screw in the center of the panel ( fig. 3). Keep the attached washer with the screw. 2. Install two AAA batteries, ensuring that the polarity (+ and –) on the batteries matches the + and – markings in the battery compartment. 3. Reattach the battery cover, making sure that the cover is seated properly. 4. Insert the screw, with the washer still attached, and tighten the screw until it is snug. Caution: Do not overtighten the screw. You may damage the washer and the remote will no longer be washable. (&. ' ' . FIGURE 3. Remote Battery Installation Getting Started To install the batteries for your keyboard 1. On the back of the keyboard, remove the battery cover by loosening both large screws on either end of the battery panel (fig. 4). Keep the attached washers with each screw. 2. Remove the rubber gasket. 3. Install two AA batteries, ensuring that the polarity (+ and –) on the batteries matches the + and – markings in the battery compartment. 4. Reattach the rubber gasket, ensuring that the four nubs on the underside of the gasket are pressed firmly into the holes in the battery compartment. This is important to keep the keyboard washable. 5. Reattach the battery cover, ensuring that it is seated properly. 6. Insert the screws, with the washers still attached, and tighten the screws until they are snug. Note: If the screws won't tighten all the way, or the battery cover isn't flush with the keyboard bottom, make sure the rubber gasket is firmly inserted into the battery compartment. Caution: Do not overtighten the screws. You may damage the washers and the keyboard will no longer be washable. !)) *(&' FIGURE 4. Keyboard Battery Installation FlipScreen Owner’s Manual Connecting a TV Cable or Antenna FIGURE 5. Rear Panel of the iCEBOX FlipScreen The iCEBOX is a 125-channel, cable-ready, stereo television. To use your iCEBOX as a television, you must first connect it to a TV signal source. To connect the TV cable • Screw the existing television cable into the TV In connection on the back of the iCEBOX (fig. 5). If space is limited, use the supplied right angle F-connector. To connect a TV antenna • Use an antenna with a connector designed to fit on to a coaxial cable connection like the one for the TV In connection at the back of the iCE- BOX (fig. 5). Satellite or Digital Cable Television Service The iCEBOX supports satellite and digital cable television service; however, when using satellite service, the iCEBOX remote or keyboard cannot be used to change channels. Continue to use your existing remote control with the set-top box. Your satellite signal may come in through the standard TV-In coxial connection. See To connect the TV cable in the previous section. Alternately, you may wish to take advantage of the higher quality of Satellite or Digital Cable by using the S-video connection. You can connect digital cable or a Direct Broadcast Satellite (DBS) system, such as DirectTV or DISH, to your iCEBOX. See To connect an S-Video source in the next section. Note: If you use an S-Video connection from your Satellite or Digital cable, you will need to use Video Mode to watch television. See Video Mode on page 41. The iCEBOX remote or keyboard cannot be used to change channels in Video Mode. Continue to use your existing remote control with the set-top box. Getting Started Connecting an S-Video Source Connecting a Camera, VCR or Video Game. Connecting the FM Radio Antenna S-Video (Super-Video) divides video information into two separate signals for a sharper, higher-quality image. Most new video cameras, camcorders, VCRs, and game machines include an S-Video jack. The iCEBOX can support one S-Video signal that can be viewed in Video Mode. Press the Video mode button repeatedly to toggle between the S- Video signal and a composite signal. You can also use the S-Video jack for Satellite or Digital Cable. For more information see Video Mode on page 41. To connect an S-Video source • Plug an S-Video cable from the camera, VCR, game machine or satellite/ cable receiver into the S-Video connection on the back of the iCEBOX. • Insert audio cables from the S-Video device into the Audio In connections in the back of the iCEBOX. Using the iCEBOX Video Mode, you can monitor another area of your home where a video camera is installed, play a video game or view a video tape in a VCR using a composite signal. Since Video Mode supports both composite and S-Video sources, you can toggle between the two signals by repeatedly pressing the Video mode button. For more information see Video Mode on page 41. Note: At this time, Video Mode supports only one Audio source which will continue to play when you toggle between Video signals. To connect an RCA Composite source • Plug a...