Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M ASSE 1016 ROUGHING-IN DIMENSIONS Recommended Tools Flat Blade Screwdriver Phillips Screwdriver Remove as much surface dirt and film using clear water and soft cotton cloth (as described above). Use any of the following to remove tough surface film and build-up: Mild liquid detergents Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions. Non-abrasive liquid polishers Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. 230mm (9) 230mm (9) 86mm (3-3/8) 34mm (1-3/8) 191mm (7-1/2) 150mm (5-7/8) 25mm (1) R510 1/2 NPT R530 3/4 NPT R510 1/2 NPT R530 3/4 NPT 48mm to 68mm (2 to 2-5/8) 1 3 5 2 4 M 9 6 8 6 5 8 TEMPERATURE CALIBRATION SET HOT LIMIT STOP 5 Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards. For 100°F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100°F. Check that arrow marking A on the KNOB MOUNT (3) still points upward after adjusting the thermostat to 100°F. If not, pull out the RED LOCKING DEVICE (5). Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow. Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards. The maximum mixed water temperature is set at 109°F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104°F or 112°F. Reinstall RED LOCKING DEVICE (5). ARROW "A" ARROW "B" 104 109 112 OPERATING THE VALVE OFF COLD HOT 4 1 Push CAP (1) over the O-RING SEAL (2). TRIM INSTALLATION 1 3 6 Push ESCUTCHEON (3) over CAP (1). Attach ESCUTCHEON (3) to VALVE (4) with the two SCREWS (5) provided. Align DIAL PLATE (6) and push DIAL PLATE (9) into place. 2 HANDLE INSTALLATION Align HANDLE BASE (1) with KNOB MOUNT (2) and push onto KNOB MOUNT (2). Install HANDLE (3) as shown. Install HANDLE SCREW (4) and tighten with screwdriver. Push KNOB CAP (5) into HANDLE (3). 4 Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: 3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim CHECK STOP (RED TO BLUE) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. Turn the water supply back on and perform the temperature adjustment in step 4. CHECK STOP (BLUE TO RED) 2 5 1 3 4 5 2 Turn on water supply on and test installed fitting. If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed. See step 3 for TRANSPOSED SUPPLY PIPING. Operate valve from off to cold to hot. Check temperature. If max mixed water temperature is to hot or to cold see step 4 and re-calibrate the valve. M 9 6 8 6 5 8 TOWNSQUARE MODEL NUMBERS CHROME BLACKENED BRONZE SATIN NICKEL 002 068 295 Replace the "YYY" with appropriate finish code CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT M962633-YYY0A HANDLE SCREW AND INDEX BUTTON M916815-YYY0A LEVER HANDLE A909834-YYY0A DIAL PLATE M908587-YYY0A HANDLE BASE A918434-0070A ESCUTCHEON SCREWS M962632-YYY0A ESCUTCHEON KIT A907090-YYY0A CAP HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2007 IN MEXICO 01-800-839-12-00 T...