Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Aube's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some regions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from region to region. • Customer Assistance If you have any questions about the product installation or operation, or concerning the warranty, contact us at: 705 Montrichard 10 rue Ampere Saint-Jean-sur-Richelieu 95500 Gonesse Quebec, Canada J2X 5K8 France Tel.: (450) 358-4600 Tel.: 33 (0) 1 34 07 99 00 Toll Free: 1-800-831-AUBE Fax: 33 (0) 1 34 07 99 19 Fax: (450) 358-4650 Email: advaube@comintes.com Email: aube.service@honeywell.com For more information on our products, go to TH131 & TH133 400-131-002-C 1/11/06 2/2 PB130-024T 400-130-002-C 1/11/06 1/1 This document describes the connections when the PB130-024T power base is used on any TH13x series thermostat. This low-voltage power base can be connected to a line-voltage load using a relay or directly to a 24-volt device. The PB130-024T is compatible with most relays; however, the following Aube relays are optimized for use with this power base: • RT850 solid-state relay (SSR) • RT850T solid-state relay (SSR) with built-in 24-V transformer • RC840 electromechanical relay • RC840T electromechanical relay with built-in 24-V transformer .. One (1) power base .. Two (2) plastic anchors .. Two (2) mounting screws .. For a new installation, choose a location about 1.5 m (5 ft.) above the floor. .. The thermostat must be installed on an inside wall facing the heating system (except for floor heating systems). .. Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a door), direct sunlight or concealed chimney or stove pipes (except for floor heating systems). The installation must be carried out by an electrician and must comply to local electrical codes. .. Turn off power to the heating system at the main electrical panel to avoid electrical shock. .. Wire the base according to your application. See typical wiring diagrams in sections 4.1 to 4.4. .. For a floor heating system installation, connect the floor sensor between the S and R terminals. .. Secure the base to the wall using the provided screws and wall anchors. .. Configure the switches located on the control module (if any). Refer to the user guide. .. Install the control module onto the base. .. Apply power to the heating system. .. Verify the installation by checking that the heating system can be turned On or Off using the thermostat. 4.1 Single SSR with Built-in Transformer 4.2 Multiple SSRs with External Transformer 4.3 Electromechanical Relay with External Transformer 4.4 Hot Water Heater Valve Maximum load: 0.5 A / 24 VAC Operating temperature: 0°C to 50°C (32°F to 122°F) Storage: -20°C to 50°C (-4°F to 122°F) Size (H • W • D): 75 x 75 x 13 mm (2.9 x 2.9 x 0.5 in) Wire gauge: 14 to 22 AWG .. Applications 1. .. Supplied Parts 2. .. Installation Guidelines 3. .. Installation Procedure 4. .. Technical Specifications 5. Electrical Panel Heater Blue Red Black Electrical Panel Heater Heater External 24 V Transformer Red Red Black Black Electrical Panel Heater External 24 V Transformer Electrical Panel External 24 V Valve Tr...
Otros modelos de este manual:Los termostatos - TH133 (344.44 kb)