Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
If you prefer to use normal recovery, slide the switch to the DISABLE position. Jumper X Wallplate Terminals YWRcGFan Heat RelayRelay RhCool Contactor or Valve Heat/Cool24V Supply Auto Recovery (SW4) DISABLE ENABLE HG HE Fan Option (SW6) 5-wire Heat/Cool System No JumperWallplate Terminals RhRcGYWRelay Supply Fan Cool 24V Cool Contactor Heat RelaySupply Heat 24V or Valve Figure 7 2-wire Heat Only System Wallplate Jumper Terminals GRhRcXX X Y W Heat 24V or Heat RelayMillivolt Supply or Valve 3-wire Heat Only System Jumper XX Wallplate Terminals GRcRhYWFan Relay Heat Relayor Valve Heat 24V Supply 3-wire Cool Only System Jumper XX Wallplate Terminals Cool Contactor Cool 24V Supply Fan Relay WYRhRcG X - No Connection Selector Switches In order for this thermostat to control your system, the system type must be specified by the selector switches on the printed circuit board inside the thermostat. ¦ Heating System Selector (HG - HE switch) The factory position for this switch is in the “HG” position. Leave it in this position if you have a gas furnace or an oil burner. If you have an electric furnace, test to see whether the Heat and Fan come on as expected after installation. If the Fan operation is normal, leave it in the “HG” position. If the Fan does not come on within a minute of the thermostat calling for heat, change the switch position to “HE”. The system selector has no effect in the cooling mode. NOTE: “HG” position is for gas and most other systems. “HE” position is for certain electric systems having a fan relay. C° / F° Selection (Celcius / Fahrenheit) Your thermostat is set for C° mode from the factory. To change to F° mode, follow these steps: ¦ Press and hold the Up key. ¦ Use a paper clip to press the reset key. ¦ Once all the LCD segments turn on, release the Up key. NOTE: To return to C° mode, press the reset key with a paper clip. Do not press any other keys during the reset process. All programs and settings will be lost when pressing RESET. OPERATION Setting Day and Time ¦ The LCD will show this information when M batteries are first installed, or after the AM Reset button is pressed. The temperature will update after a few seconds. ¦ During time and day setting mode, the temperature and program displays will go blank. 4 TEMP ¦ Example: Set the Thermostat to the current time of 2:16 pm on Saturday. Refer to the Steps below. STEP 1: day/time ¦ Press to enter time and day setting mode. The current hour and the AM / PM indicator will be flashing. ¦ Press to change the Hour up or down to the current hour. Note the AM / PM indicator, as the display will change at 12 AM and 12 PM. M AM STEP 2: day/time ¦ Press again to change from hour setting to minute setting. The current minute will be flashing. ¦ Press to change the Minute up or down to the current minute. M PM (Continued) ® Setting Day and Time (Continued) STEP 3: day/time ¦ Press again to change from minute setting to day setting. The current day will be flashing. ¦ Press to change the Day up or down to the current day. M PM STEP 4: day/time ¦ Press again to change back to the SA normal display. or PM hold 2 TEMP /return NOTE: You may press hold at any time during Day and Time setting to return /return to the normal display. 12 Hr. / 24 Hr. Time Format Your thermostat is set from the factory in normal 12 (AM / PM) time format. To change to 24 hour (military) time, press program at any time while the Hour, Minute, or Day is flashing to toggle between the 12 hour and 24 hour formats. The AM / PM indicator will not be displayed in 24 hour mode. Both the current time and all programs will automatically change to the selected format. PROGRAMMING The following time and temperature settings are pre-programmed into the thermostat: Temperature in C° (F°) Program Number Time Heat Cool 1 6:00 am 20°C (68°F) 26°C (78°F) 2 8:00 am 16°C (60°F) 29°C (85°F) 3 4:00 pm 20°C (68°F) 26°C (78°F) 4 10:00 pm 16°C (60°F) 28°C (82°F) ¦ All 7 days of the week have the same default programs. Personal Program Schedule ¦ You can revise the factory programs to match your own schedule. Use this Personal Program Schedule to determine which times and temperature settings match your comfort and energy saving requirements. Use a pencil so you can revise your records each time you change your program settings. Heating Day Program 1 Program 2 Program 3 Program 4 Monday – Friday Time Temp Time Temp Time Temp Time Temp Saturday – Sunday Time Temp Time Temp Time Temp Time Temp Cooling Day Program 1 Program 2 Program 3 Program 4 Monday – Friday Time Temp Time Temp Time Temp Time Temp Saturday – Sunday Time Temp Time Temp Time Temp Time Temp Revising Programs ¦ Familiarize yourself with manually changing programs, so that you can easily modify the programs as your comfort needs change. Follow the steps below to change the program times and temperatures. NOTE: 1) The program time can be set in 10-minute increments. 2) The program temperature can be set in increments of 1°C (1°F). 3) ...
Otros modelos de este manual:Los termostatos - 47110A (295.57 kb)
Los termostatos - 47110A (295.57 kb)