Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
OWNER’SMANUALOWNER’S MANUAL OPTIONAL HUMIDITY MODULEOPTIONAL HUMIDITY MODULE Accepts theAccepts the COMMERCIALCOMMERCIAL THERMOSTATTHERMOSTAT P/NP/N 33CS4500133CS450 01 AUTO I2:00 Su Pm HEAT COOL 72 74 Carrier Carrier CAUTION Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults. CAUTION NEVER PUT MORE THAN ONE JUMPER ON THE SAME MISC JUMPER BLOCK! THIS MAY DAMAGE YOUR THERMOSTAT. MISC3 OK MISC3 NOTE: Due to variations in environmental conditions, it is not always possible to achieve the desired humidification or dehumidification setpoint. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4Z95 Thermostat 33CS450-01 Tested to Comply with FCC Standards FOR HOME OR OFFICE USE FCc Page i HowtoUseThisManualHow to Use This Manual Carrier HowtoUseThisManualHow to Use This Manual Carrier The Table of Contents divides the thermostat features into sections making it easier to quickly find information. The first page of each section contains a more detailed list of the contents within that section, such as the example page shown below. SECTION 14 TimersandDeadbandsTimers and Deadbands Carrier Section 14 Contents: Adjusting the Heat/Cool Differential..............................14.2 Adjusting the Cycles Per Hour..................................14.3 Adjusting the Deadband..........14.4 Adjusting the Minutes of Run-Time Before the Header shows section # and title of section Section contents 14 Next Stage...............................14.6 Selecting 2nd Stage Turn Off Temperature.....................14.7 Visible section tab on the side of the page Section and page # Page 14.1 In addition, this manual also has an Index to help you find any information regarding this thermostat quickly. Page ii GlossaryofTermsGlossary of Terms Carrier GlossaryofTermsGlossary of Terms Carrier Auto-Changeover: A mode in which the thermostat will turn on the heating or cooling based on room temperature demand. Configurable Output Jumper: Using jumpers on the thermostat you can configure the MISC1, MISC2, and MISC3 terminals to control humidification, dehumidification, 2nd stage cooling, 3rd stage heating, and a programmable output. Cool Setpoint: The warmest temperature that the space should rise to before cooling is turned on (without regards to deadband). Deadband: The number of degrees the thermostat will wait, once setpoint has been reached, before energizing heating or cooling. Dehumidify: To reduce the amount of moisture in the air. Differential: The forced temperature difference between the heat setpoint and the cool setpoint. Heat Setpoint: The coolest temperature that the space should drop to before heating is turned on (without regards to deadband). Humidify: To increase the amount of moisture in the air. Icon: The word or symbol that appears on the thermostat display. Mode: The current operating condition of the thermostat (i.e. Off, Heat, Cool, Auto, Program On). Non-Programmable Thermostat: A thermostat that does not have the capability of running the Time Period Programming. Programmable Thermostat: A thermostat that has the capability of running the Time Period Programming. Reheat: Running the cooling and 2nd stage strip heaters at the same time in order to dehumidify the air without cooling down the room temperature. Temperature Swing: Same as Deadband. Time Period Programming: A program that allows the thermostat to automatically adjust the heat setpoint and/or the cool setpoint based on the time of day. Page iii T TT a aa b bb l ll e ee o oo f ff C CC o oo n nn t tt e ee n nn t tt s ss Carrier Page iv Quick Start Getting to Know YourThermostat Setting Clock and Day Basic Operation Viewing Temperatureand HumidityProgramming theDaily ScheduleProgramming theFan OperationThermostat DisplayOptions Humidification Dehumidification Viewing EquipmentRun Times Electric Heat and Heat Pump Operation Timers and Deadbands Using theProgrammable OutputProgramming RemoteSensor Operation Dry Contact Operation Energy SaveOperationProgramming the RunTime Alerts Programming theHoliday ModeConfiguring the MISCOutputsFactory Defaults, Calibration, and Sensors Accessories Advanced Setup Table Light ActivatedOperation SECTION 1 Q QQ u uu i ii c cc k kk S SS t tt a aa r rr t tt Carrier 1 Section 1 Contents: Setting the Clock and Day...........1.2 Selecting the Heat or Cool Mode............................................1.3 Selecting Your Desired Temperature................................1.4 Using the Fan Button...................1.4 Note: Following the instructions in this section will allow you to operate your thermostat using the factory default settings. These settings are depicted in the illustrations throughout this manua...