Votos - 0, Puntuación media: 5
(
)
)
|
Resumen del manual
1 CONFIGURATION ..............................1-4 I. Thermostat Display ....................... 1 II. Heat or Cool Indicator .................... 1 III. Thermostat Front Panel Buttons ............ 2 IV. Thermostat Programming Buttons .......... 2 V. Set Clock ................................ 3 VI. Programming Thermostat Schedules ........ 3 OPERATION ................................... 5 I. Auto-Changeover ......................... 5 II. Two-Stage Operation ...................... 5 III. Clock Backup ............................ 5 IV. Fan Operation ............................ 5 V. Emergency Heat .......................... 5 VI. Electric Heat ............................. 5 VII. Holiday Mode ............................ 5 IMPORTANT: Read entire instructions before starting the installation. GENERAL Bryant’s 7-day, commercial, programmable thermostats are wall-mounted, low-voltage thermostats which maintain room temperature by controlling the operation of an HVAC (heating, ventilation, and air conditioning) system. Separate heating and cooling set points and auto-changeover capability allow occupied and unoccupied programming schedules for energy savings. All thermostats allow up to 3 occupied and one unoccupied time/temperature setting to be programmed per 24-hour period. Each thermostat stores programs for 7 independent days. Batteries are not required. During power interruption the internal NEVERLOST™ memory stores programs for an unlimited time. IMPORTANT: The thermostat has a configurable security level. If certain functions are not available (changing set points, changing programming schedules), the thermostat security level may be configured to exclude those functions. Call the installer to reconfigure the security level. Cancels: New OM TSTAT-6 11/1/98 CONFIGURATION I. THERMOSTAT DISPLAY The thermostat display is located in the center of the thermostat. See Fig. 1. The following information can be displayed on the screen: • mode (OFF, HEAT, COOL, AUTO, or PROGRAM ON) • fan setting (FAN ON or blank) • override indication • room temperature • desired temperature • service filter indicator • time of day • day of the week • schedule period (Occupied 1, 2, or 3; or Unoccupied) • setup indicator (programming mode) • lock indicator • start/stop indicator (schedule period program mode) Fig.1—ThermostatDisplay II. HEAT OR COOL INDICATOR A Heat or Cool indicator is located on the bottom left cover of the thermostat. See Fig. 2. The light will be red if the thermostat is in Heating mode. The light will be green if the thermostat is in Cooling mode. III. THERMOSTAT FRONT PANEL BUTTONS The thermostat has buttons on the front cover which are used to raise or lower the desired set point and override the current program. See Fig. 2. A. Set Point Buttons The UP ARROW and DOWN ARROW buttons will raise or lower the current desired temperature set point. If the thermostat is in AUTO mode, pressing the UP ARROW or DOWN ARROW buttons will adjust both the heating and cooling set points. Pressing the UP ARROW or DOWN ARROW buttons in Cooling mode will adjust only the cooling set points. Pressing the UP ARROW or DOWN ARROW buttons in Heating mode will adjust only the heating set points. The UP ARROW and DOWN ARROW buttons are also used in Programming mode. B. Override Button The Override button is used to force the thermostat from Unoccupied mode into the Occupied 1 mode comfort settings. The Override period will be set at 30 minutes. The thermostat will then return to Unoccupied mode. To increase the amount of time in Override mode, press the Override button again. Thirty minutes of override time will be added for each time the Override button is pressed up to a maximum of 4 hours. After the 4-hour limit has been reached, press the Override button again to cancel Override mode. While in Override mode, the Override icon and the Occupied 1 icon will be displayed on the thermostat. The time of day and the minutes remaining in Override mode will alternate on the thermostat display. The set points are adjustable with the UP ARROW and DOWN ARROW keys during Override mode. NOTE: If the thermostat is in Occupied mode and the Override button is pressed, the thermostat will go into Unoccupied mode immediately. The thermostat will remain in Unoccupied mode until the next Occupied start time. IV. THERMOSTAT PROGRAMMING BUTTONS The thermostat has programming buttons which are used to change the set points of the thermostat, set the modes, and program schedules. The programming buttons are accessible from underneath the thermostat cover. To access the programming buttons, pull on the hinged thermostat cover. See Fig. 3. The programming buttons are: Mode, Fan, Holiday, Program, and Set Clock. The UP ARROW and DOWN ARROW buttons are used to scroll through programming set points. The buttons are also used to answer yes or no. A. Keypad Lock The thermostat has a keypad lockout feature which will not acknowledge front panel buttons until the l...