Votos - 3, Puntuación media: 4 ( )

Fabricar: Accusplit Tamaño del archivo: 479.79 kb Nombre del archivo: Idioma del manual:

Detailed uses of the buttons are different in particular functions and will be described later in the instructions. Pressing [MODE] button will toggle among the modes above. Note that there is no auto-return function in the stopwatch. Whenever you change modes, the stopwatch will remain in that mode until the [MODE] button is pressed again Each time you enter a mode, a message will be displayed for a second before you enter the mode: Note:-In the following descriptions, items printed in dark gray stand for flashing digits. . Normal Time Mode . The starting point for operating your stopwatch is NORMAL TIME. If NORMAL TIME is not displayed, press [Mode] until it is. . Year : - 2001 Date : - January 1 Day of week : - Monday Time : -12:00 am The display format is as below : 2 0 0 1 year W E 1 -3 day, month - date A 1 0 : 3 5' 3 0 hr : min second During clock display, press [START] to switch between 12Hr and 24Hr display mode. To toggle chime ON or OFF, you can press [RESET]. The bell icon will be ON and OFF correspondingly. Normal Time Setting Press and hold [RECALL] for 2 seconds to enter setting mode. The normal time setting starts with second. The second digits will then be flashing.You can change the flashing digit by pressing [START] button.To speed up the setting you can press and hold [START] for longer than 2 seconds to activate fast setting. To select other digits, press [RESET] button. The setting order is: Second, Minute, Hour, Year, Month, Date, month-date (m-d) or date-month (d-m), Sound ON or OFF, Contrast (darkness of the digits - default is 9), then back to Second, and recycles again. Note: when the second is to be set, press [START] to reset the second digits to zero. At the end of setting, press [RECALL] or [MODE] to exit from the setting mode and back to Normal Time Display. Display for Sound ON or OFF setting :( Let the current status be "ON".) SOUnd On Press [START] to toggle Sound ON or OFF. SOUnd On Display for contrast adjustment:( Let the current contrast be "5") COnT 5 Press [START] consecutively to advance the contrast up to 16, then cycle back to 1. COnT The contrast setting will be shown on 16 the display. NOTE: -The hour digits may be displayed in 12hr or 24hr format. -The year digits can be set from 2000 to 2099. The date adjusts automatically for odd and even months including February of leap years. The day of week also adjusts automatically after you set the date. Alarm Time Mode Press [MODE] until you enter Alarm mode. This mode is used for displaying the daily alarm time and allows you to enable or disable the alarm. When you enter the Alarm Time mode, the display shows the alarm time on the upper line while the date is shown in the middle of the display and the normal time is on the lower line. AL P 3 : 3 0 TU 1 -3 A 1 0 : 3 5' 3 0 To toggle the alarm ON or OFF, press [RESET]. When alarm is ON, the indicator "(((o)))" will be ON while it will be turned off when alarm is disabled. When alarm time is reached, the alarm signal will sound for 60 seconds. Press any button to stop the alarm sound. Setting Alarm Time Press and hold [RECALL] for 2 seconds to activate the alarm setting. The alarm "minute" digits will flash as an indication. Adjust the flashing digit by pressing [START]. To set the alarm hour digits, press [RESET] to switch to hour digits and then press [START] to adjust. Press [RECALL] or [MODE] to exit from Alarm setting mode. Chronograph and Recall Mode Press [MODE] until you enter the Chrono mode. The stopwatch can measure up to 19 hours. 59 minutes, 59.99 seconds. When you enter the Chronograph mode, the display format is as below. {000} 0: 00' 00" 00 SPLIT 0: 00' 00" 00 LAP STOP 0: 00' 00" 00 The upper line shows the split time, the middle line shows the lap time and the accumulated elapsed time is displayed on the lower line. Whenever the stopwatch stops running, the "STOP" indicator will be ON. Press the button [START/STOP] to start the stopwatch. As it runs, the current elapsed time is shown on the lower line. {000} 0: 00' 00" 00 SPLIT 0: 00' 00" 00 LAP RUN 0: 03' 35" 52 To view the current split / lap time, you can press [LAP/SPLIT]. {001} 0: 10' 43" 35 SPLIT 0: 10' 43" 35 LAP RUN 0: 10' 43" 35 The number of split/lap times is shown on the upper left corner. The corresponding split and lap times are displayed on the upper and middle line. Press [LAP/SPLIT] again, the next split/lap time will be shown and the number of split/lap time is updated. {002} 0: 15' 10" 94 SPLIT 0: 04' 27" 59 LAP RUN 0: 15' 10" 94 The stopwatch (Model 790M & 790MDEC) can store up to 500 split / lap times. The split/lap times can be stored into the memory as you press [LAP/SPLIT] to view the current split/lap time. Meanwhile, the lap and split time will be frozen for 5 seconds. After this 5-second period, the lap and split time will return to normal. In addition, the fastest lap, the slowest lap, and the averages of all laps will also be recorded. As you press [STOP] to stop the chrono...

Descargar ahora

Introduzca dos números de la imagen: