Manual de usuario Datalogic Scanning, modelo QUICKSCAN QD 2300
Page references are also provided for feature descriptions and programming bar codes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 30. Standard Defaults Parameter Default Your Setting Page Number General Features Set Default Parameter Restore Defaults 21 Beeper Tone Medium 22 Beeper Volume High 22 Power Mode Continuous On 23 Scan Line Width Full Width 25 Laser On Time 3.0 Sec 25 Beep After Good Read Enable 26 Transmit Label ID None 26 Global Prefix/Suffix Data As Is 28 Prefix Value 7013 29 Suffix Value 7013 29 FN1 Substitution Values Set 30 Transmit “No Read” Message Disable 30 Keyboard Wedge Host Parameters Keyboard Wedge Host Type IBM PC/AT& IBM PC Compatibles1 57 Country Types (Country Codes) North American 58 Ignore Unknown Characters Send 59 1User selection is required to configure this interface and this is the most common selection. Product Reference Guide Parameter Default Your Setting Page Number Keystroke Delay No Delay 60 Intra-Keystroke Delay Disable 60 Alternate Numeric Keypad Emulation Disable 61 Caps Lock On Disable 61 Caps Lock Override Disable 62 Convert Wedge Data No Convert 62 Function Key Mapping Disable 63 FN1 Substitution Disable 63 Send and Make Break Send 63 RS-232 Host Parameters RS-232 Host Types Standard 36 Baud Rate 9600 37 Parity Type None 38 Stop Bit Select 1 Stop Bit 39 Data Bits (ASCII Format) 8-Bit 39 Check Receive Errors Enable 40 Hardware Handshaking None 41 Software Handshaking None 43 Host Serial Response Time-out 2 Sec 45 RTS Line State Low RTS 46 Beep on Disable 46 Intercharacter Delay 0 msec 47 Nixdorf Beep/LED Options Normal Operation 48 Ignore Unknown Characters Send Bar Code 48 USB Host Parameters USB Device Type HID Keyboard Emulation 77 USB Country Keyboard Types (Country Codes) North American 78 USB Keystroke Delay No Delay 80 1User selection is required to configure this interface and this is the most common selection. 152 QuickScan® L Parameter Default Your Setting Page Number USB CAPS Lock Override Disable 80 USB Ignore Unknown Characters Send 81 Emulate Keypad Disable 81 USB FN1 Substitution Disable 82 Function Key Mapping Disable 82 Simulated Caps Lock Disable 83 Convert Case No Case Conversion 83 UPC/EAN UPC-A Enable 99 UPC-E Enable 99 UPC-E1 Disable 100 EAN-8/JAN 8 Enable 101 EAN-13/JAN 13 Enable 101 Bookland EAN Disable 101 Decode UPC/EAN/JAN Supplementals (2 and 5 digits) Ignore 102 Decode UPC/EAN/JAN Supplemental Redundancy 7 104 Transmit UPC-A Check Digit Enable 104 Transmit UPC-E Check Digit Enable 105 Transmit UPC-E1 Check Digit Enable 105 UPC-A Preamble System Character 106 UPC-E Preamble System Character 107 UPC-E1 Preamble System Character 108 Convert UPC-E to A Disable 109 Convert UPC-E1 to A Disable 109 EAN-8/JAN-8 Extend Disable 110 UCC Coupon Extended Code Disable 110 Code 128 Code 128 Enable 111 1User selection is required to configure this interface and this is the most common selection. Product Reference Guide Parameter Default Your Setting Page Number UCC/EAN-128 Enable 111 ISBT 128 (non-concatenated) Enable 112 Code 39 Code 39 Enable 112 Trioptic Code 39 Disable 113 Convert Code 39 to Code 32 (Italian Pharmacy Code) Disable 113 Code 32 Prefix Disable 114 Set Length(s) for Code 39 2 to 55 114 Code 39 Check Digit Verification Disable 116 Transmit Code 39 Check Digit Disable 116 Code 39 Full ASCII Conversion Disable 117 Buffer Code 39 Disable 118 Code 93 Code 93 Disable 120 Set Length(s) for Code 93 4 to 55 121 Code 11 Code 11 Disable 122 Set Lengths for Code 11 4 to 55 123 Code 11 Check Digit Verification Disable 125 Transmit Code 11 Check Digit(s) Disable 126 Interleaved 2 of 5 (ITF) Interleaved 2 of 5 (ITF) Enable 126 Set Lengths for I 2 of 5 14 127 I 2 of 5 Check Digit Verification Disable 129 Transmit I 2 of 5 Check Digit Disable 129 Convert I 2 of 5 to EAN 13 Disable 130 Discrete 2 of 5 (DTF) Discrete 2 of 5 Disable 130 Set Length(s) for D 2 of 5 12 131 1User selection is required to configure this interface and this is the most common selection. 154 QuickScan® L Parameter Default Your Setting Page Number Chinese 2 of 5 Enable/Disable Chinese 2 of 5 Disable 132 Codabar (NW - 7) Codabar Disable 133 Set Lengths for Codabar 5 to 55 133 CLSI Editing Disable 135 NOTIS Editing Disable 136 MSI MSI Disable 136 Set Length(s) for MSI 2 to 55 137 MSI Check Digits One 138 Transmit MSI Check Digit Disable 139 MSI Check Digit Algorithm Mod 10/Mod 10 139 GS1 DataBar (RSS) DataBar Omnidirectional (RSS -14) Disable 140 DataBar Limited Disable 140 DataBar Expanded Disable 140 Convert DataBar to UPC/EAN Disable 141 Symbology - Specific Security Levels Redundancy Level 1 142 Security Levels 0 144 Bi-directional Redundancy Disable 145 1User selection is required to configure this interface and this is the most common selection. Product Reference Guide NOTES 156 QuickScan® L Appendix C Programming Reference Datalogic Label ID Identifie...
