Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
2. When an optional Cutter Module is fitted, clean the print headusing the Print Head Cleaner supplied with the Cutter Module, as the picture shows. This chapter describes how to perform routine maintenance. To ensure the continuous high quality operation of the printer, refer to the following table and perform a regular maintenance routine. Cleaning cycle Frequency High throughput Every day Every ribbon roll or media roll Once To maintain the printer performance and print quality, please clean the printer regularly, or whenever the media or ribbon is replaced. 1. Turn off the power and unplug the printer. 2. Set the Head Lever to the “OPEN” position. 3. Open the Top Cover and Right Side Cover. 4. Open the Head Lock Plate. 5. Remove the ribbon and media from the printer. 6. Clean the Print Head Element with a Print Head Cleaner, or a cotton swab or soft cloth slightly moistened with absolute ethyl alcohol. Print Head Cleaner Print Head Element When the Cutter Module is fitted. Print Head Cleaner (Supplied with the optional Cutter Module Cutter Module) E4- 1 4. MAINTENANCE ENGLISH VERSION EO1-33057 4.1 Cleaning 4.1.1 Print Head/Platen (Cont.) 4.1.2 Pinch Roller NOTE: Be sure to set the Head Lever to Position 2, otherwise the Pinch Roller cannot be removed. Position 2 Head Lever CAUTION! Do not pull hard on the Ribbon End Sensor Plate. Doing so may damage the Ribbon End Sensor Harness, causing a printer failure. 7. Wipe the Platen with a soft cloth slightly moistened with absolute ethyl alcohol Platen 1. Turn off the power and unplug the printer. 2. Set the Head Lever to the “OPEN” position. 3. Open the Top Cover and Right Side Cover. 4. Open the Head Lock Plate. 5. Turn the Pinch Roller Lever clockwise to release the Pinch Roller. Pinch Roller Lever 6. Remove the ribbon and media from the printer. 7. Set the Head Lever to the Position 2. 8. Remove the White Screw and detach the Ribbon End Sensor Plate in the direction of the arrows. 1 2 Ribbon End Sensor Plate White Screw Ribbon End Sensor Plate E4- 2 4. MAINTENANCE ENGLISH VERSION EO1-33057 4.1 Cleaning 4.1.2 Pinch Roller (Cont.) CAUTION! When re-installing the Pinch Roller Ass’y on the printer, remove the slack of the Ribbon End Sensor Harness as far as possible by pushing it into the opening (indicated by the arrow). Failure to do this may cause the harness to be caught by the Ribbon End Sensor Plate, resulting in a printer failure. Ribbon End Sensor Harness 9. Take out the Pinch Roller Ass’y from the printer. Pinch Roller Ass’y 10. Wipe the Pinch Roller Ass’y with a soft cloth slightly moistened with absolute ethyl alcohol. Pinch Roller Ass’y 11. After cleaning the Pinch Roller Ass’y, place it in position, and raise the both Pinch Roller Plates. Pinch Roller Plate Pinch Roller Ass’y E4- 3 4. MAINTENANCE ENGLISH VERSION EO1-33057 4.1 Cleaning 12. Attach the Ribbon End Sensor Plate to the printer. 4.1.2 Pinch Roller (Cont.) (1)Engage the notches on the both sides of the Ribbon End Sensor Ribbon End Sensor Plate Plate with the Positioning Pins of the printer. Notch Slot Positioning Pin Positioning Pin (2) Fit the tip of the Pinch Roller Plates into the slot in the Ribbon End Sensor. Ribbon End Sensor Plate Pinch Roller Plate Slot E4- 4 4. MAINTENANCE ENGLISH VERSION EO1-33057 4.1 Cleaning 4.1.3 Under the Media Guides 1. Turn off the power and unplug the printer.. 2. Set the Head Lever to the “OPEN” position NOTE: 3. Open the Top Cover and Right Side Cover. Be careful not to lose the removed 4. Open the Head Lock Plate. screws. 5. Turn the Pinch Roller Lever clockwise to release the Pinch Roller. 6. Remove the ribbon and media from the printer. 7. Remove the screws to detach the Media Guide. Screw Media Guide Screw Media Guide 8. Remove the jammed media, if any. 9. Wipe dirt, dust, or paper particles from the media path. Media Path 10. Wipe dust and adhesive off the Media Guides with a soft cloth moistened with alcohol. Media Guide 11. Re-install the Media Guides using the screws. E4- 5 4. MAINTENANCE ENGLISH VERSION EO1-33057 4.1 Cleaning 4.1.4 Covers and Panels Wipe the covers and panels with a dry soft cloth or a cloth slightly moistened with mild detergent solution. CAUTION! 1. DO NOT POUR WATER directly onto the printer. 2. DO NOT APPLY cleaner or detergent directly onto any cover or panel. 3. NEVER USE THINNER OR OTHER VOLATILE SOLVENT on the plastic covers. 4. DO NOT clean the panel or covers with alcohol as it may cause them to discolour, loose their shape or develop structural weakness. E4- 6 4. MAINTENANCE ENGLISH VERSION EO1-33057 4.1 Cleaning 4.1.5 Optional Cutter Module 1. Loosen the two screws and remove the Cutter Cover. As the bottom of the Cutter Cover is fitted onto the Cutter Attachment WARNING! Screw, slightly lift and detach the Cutter Cover. 1. Be sure to turn the power off before cleaning the cutter unit. 2. As the cutter blade is sharp, care should be taken not to injure yourself when cleaning. Screw Cutter Cover Cutter Attachment Scr...
Otros modelos de este manual:Equipo de Taller - EO1-33057D (1.65 mb)
Equipo de Taller - EO1-33057 (1.65 mb)