Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
.. Problem No file has been correctly selected for uploading. .. Solution Select a file(s) to be uploaded and retry the upload. [2.2] ActiveSync (Infrared) Choosing "2:ActiveSync (Infrared)" on the Communication menu connects the BHT to the host computer via the Infrared interface port. Upon completion of connection, the screen shown at left appears. For details about the configuration of the host computer andconnection using ActiveSync, refer to Chapter 3, Section 3.5"ActiveSync." When connecting the BHT to the host computer using ActiveSync (Infrared), arrange the BHT andhost computer with their Infrared ports facing directly each other. When the CU-401 with RS-232C interface is used to connect the BHT withthe host, no ActiveSync can be used. The BHT can be setup so that ActiveSync, which allows connection with the host computer, beginsautomatically if the BHT is placed on the CU-421 while turned on. For further details, refer to Section 2.5.4, "[3.3] Device Menu". If ActiveSync connection succeeds If ActiveSync connection succeeds, the BHT beeps once and displays the ActiveSync icon (circled in red at left) in the task tray. If ActiveSync connection fails If ActiveSync connection fails, the BHT beeps once and does not display the ActiveSync icon. [2.3] ActiveSync (Serial) Choosing "3:ActiveSync (Serial)" on the Communication menu connects the BHT to the host computer via the connector interface port. After a connection is established, the screen shown at left appears. For details about the configuration of the host computer andconnection using ActiveSync, refer to Chapter 3, Section 3.5: "ActiveSync." If ActiveSync connection succeeds If ActiveSync connection succeeds, the BHT beeps once and displays the ActiveSync icon (circled in red at left) in the task tray. If ActiveSync connection fails If ActiveSync connection fails, the BHT beeps once and does not display the ActiveSync icon. [2.4] ActiveSync (USB) Choosing "4:ActiveSync (USB)" on the Communication menu connects the BHT to the host computer via the USB interface port. Upon completion of connection, the screen shown at left appears. For details about the configuration of the host computer andconnection using ActiveSync, refer to Chapter 3, Section 3.5"ActiveSync." The BHT can be setup so that ActiveSync, which allows connection with the host computer, begins automatically when the USB cable is plugged into the BHT when it is turned on. For further details, refer to Section 2.5.4, "[3.3] Device Menu". If ActiveSync connection succeeds If ActiveSync connection succeeds, the BHT beeps once and displays the ActiveSync icon (circled in red at left) in the task tray. If ActiveSync connection fails If ActiveSync connection fails, the BHT beeps once and does not display the ActiveSync icon. [2.5] ActiveSync (RF) Choosing "5:ActiveSync (RF)" on the Communication menu connects the BHT to the host computer via the RF interface port. Before proceeding to "ActiveSync (RF)," you need to: - Set up a partnership between the host computer and BHT by running "ActiveSync (Infrared).", "ActiveSync (Serial)" or "ActiveSync (USB)" - Make the RF settings according to the procedure given in "2.6 Wireless Zero Configuration (WZC) Menu" If the RF settings are not made correctly, "ActiveSync (RF)" cannot run. When the BHT is opening the RF device and connecting to thenetwork, it displays the screen shown at left. Connection to the network may take several tens of seconds depending upon the network environment. (When the DHCP isused for getting an IP address, connection to the network willrequire more time than when the IP address is fixed.) If connection to the network cannot be completed, the RF settingsmay have not been made correctly. Check the RF settings again. . Upon completion of connection to the network, the screen shown atleft appears. Select "Network Connection" as connection method and select thename of the host computer in the Connect to box. Then tap the Connect button. . Upon completion of connection by ActiveSync, the screen shown atleft appears. If connection to the network fails If connection to the network fails, the BHT beeps three times and displays the following screen. .. Solution The RF settings may have not been made correctly. According to theprocedure given in "2.6 Wireless Zero Configuration (WZC) Menu," make the correct RF settings. If no partnership has been set up If no partnership has been set up between the host computer and BHT, the BHT beeps three times and displays the following screen. .. Solution Set up a partnership according to the procedure given in Chapter 3. Section 3.5.2, "Connection Using ActiveSync." [ 3 ] System Properties Choosing "3:System Properties" in System Menu calls up the window shown at left. [1] Barcode: Opens the Barcode menu. [2] Beeper/Vibration: Opens the Beeper/Vibration menu. [3] Control Panel: Opens the Control Panel window. [4] File System: Opens the File System menu. [5] Power Management: Opens the Power Man...
Otros modelos de este manual:Equipo de Taller - 400BW-CE (4.33 mb)