Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
4.8 CHANGING DEFAULT SETTINGS Once your reader is setup, you can change the default parameters to meet your application needs. Refer to the preceding paragraphs for initial configuration in order to set the default values and select the interface for your application. In this manual, the configuration parameters are divided into logical groups making it easy to find the desired function based on its reference group. The first four groups are for Standard Interface parameter configuration: RS232 USB WEDGE PEN EMULATION The following parameter groups are common to all interface applications: DATA FORMAT parameters regard the messages sent to the Host system for all interfaces except Pen Emulation. POWER SAVE manages overall current consumption in the reading device. READING PARAMETERS control various operating modes and indicator status functioning. DECODING PARAMETERS maintain correct barcode decoding in certain special reading conditions. CODE SELECTION parameters allow configuration of a personalized mix of codes, code families and their options. ADVANCED FORMATTING PARAMETERS allow code concatenation and advanced formatting of messages towards the Host. It cannot be used with Pen Emulation connections. RADIO PARAMETERS (Mx30 series only) allow configuration of radio control parameters. RS232 PARAMETERS All Gryphon™ Dx30 Series readers + Gryphon™ Mx30/OM-Gryphon™ configurations only .. BAUD RATE .. .. PARITY .. .. DATA BITS .. .. STOP BITS .. .. HANDSHAKING .. .. ACK/NACK PROTOCOL .. .. FIFO .. .. INTER-CHARACTER DELAY .. .. RX TIMEOUT .. .. SERIAL TRIGGER LOCK .. 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. .. = Read the code and follow the procedure given .. = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page. BAUD RATE 300 baud ICD1XI 600 baud 1200 baud ICD2[I ICD3^I 2400 baud 4800 baud ICD4aI ICD5dI .. 9600 baud 19200 baud ICD6gI ICD7jI 38400 baud ICD8mI PARITY .. none ICC0SI even parity ICC1VI odd parity ICC2YI DATA BITS 7 bits ICA0OI .. 8 bits ICA1RI 9 bits ICA2UI STOP BITS .. 1 stop bit ICB0QI 2 stop bits ICB1TI HANDSHAKING .. disable ICE0WI hardware (RTS/CTS) ICE1ZI software (XON/XOFF) ICE2]I RTS always ON ICE3`I See par. 5.1.1 for details. ACK/NACK PROTOCOL .. disable IER0sI enable IER1vI See par. 5.1.2 for details, particularly on implementing this parameter with Gryphon™ Mx30. FIFO disable IEC0UI .. enable IEC1XI See par. 5.1.3 for details. INTER-CHARACTER DELAY delay between characters transmitted to Host ICK3I Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 milliseconds .. delay disabled RX TIMEOUT timeout control in reception from Host ICL5I Read 2 numbers from the table where: 00 = TIMEOUT disabled 01-99 = TIMEOUT from .1 to 9.9 seconds .. rx timeout 5 seconds See par. 5.1.4 for details. SERIAL TRIGGER LOCK .. disabled ICR0qI enable and select characters ICR1tI Read 2 characters from the Hex/Numeric table in the range 00-FE where: . First Character enables device trigger . Second Character inhibits device trigger until the first character is received again. USB PARAMETERS .. USB-COM Handshaking, Ack/Nack protocol, FIFO, Inter-character delay, Rx timeout, Serial trigger lock .. .. USB-KBD Keyboard nationality, FIFO, Inter-character delay, Inter-code delay, Control character emulation, USB keyboard speed .. .. USB-IBM No parameter selection required. .. 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. .. = Read the code and follow the procedure given .. = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page. HANDSHAKING .. disable ICE0WI hardware (RTS/CTS) ICE1ZI software (XON/XOFF) ICE2]I RTS always ON ICE3`I See par. 5.1.1 for details. ACK/NACK PROTOCOL .. disable IER0sI enable IER1vI See par. 5.1.2 for details. FIFO disable IEC0UI .. enable IEC1XI See par. 5.1.3 for details. INTER-CHARACTER DELAY delay between characters transmitted to Host ICK3I Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 milliseconds .. delay disabled RX TIMEOUT timeout control in reception from Host ICL5I Read 2 numbers from the table where: 00 = TIMEOUT disabled 01-99 = TIMEOUT from .1 to 9.9 seconds .. rx timeout 5 seconds See par. 5.1.4 for details. SERIAL TRIGGER LOCK .. disabled ICR0qI enable and select characters ICR1tI Read 2 characters from the Hex/Numeric table in the range 00-FE where: . First Character enables device trigger . Second Character inhibits device trigger until the first character is received again. KEYBOARD NATIONALITY Not Available for USB-KBD-ALT-MODE Interface This parameter default value is restored through the Interface Selection code and not Restore Default. Belgian IFJ7yI English French IFJ4pI IFJ2jI German Italian IFJ3mI IFJ1gI Japanese Spanish IFJ8|I IFJ6v...
Otros modelos de este manual:Equipo de Taller - GRYPHONTM DX30 (4.47 mb)