Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
For CR4004/ 4104/ 4214: Power connector cable and I/O bracket plate. INSTALLATION CR4000 / 4100 / 4210 Connect the drawer to POS system/printer as shown below: CR4001 / 4101 / 4211 CASH DRAWER With Printer Interface 8P Telephone Jack 8P Telephone Plug 6P Telephone Plug Output to drawer POS System or Printer Ground Rear View Control signal input 1). Connect the drawer serial I/P port to the computer COM port. Connect the power adapter output to the Power Input jack 2). No other RS232C devices should be connected to the serial O/P port. 3).Set position 3 of S2 to OFF and position 4 of S2 to ON. Please refer to rear panel illustration. CR4002 / 4102 / 4212 1). Connect the drawer serial I/P port to the computer COM port. Connect the power adapter output to the Power Input jack. 2). Other RS232C device can be connected to the serial O/P port when needed as long as the security code makes no influence to this RS232C device. 3).Set position 3 of S2 to ON and position 4 of S2 to OFF. Set S1 for security code to open cash drawer. In normal practice, the security code is suggested to be a non-displayable ASCII character, for example, a hexadecimal number between 01 to 1F. Please refer to rear panel illustration below. CR4003 / 4103 / 4213 1). Connect the drawer parallel I/P port to the computer LPT port. Connect the power adapter output to the Power Input jack. 2). Other parallel device such as a printer can be connected to the parallel O/P port when needed as long as the Security code makes no influence to this parallel device. 3 3). Set S1 for security code to open cash drawer. In normal practice, the security code is suggested to be a non-displayable ASCII character. For. example, a hexadecimal number between 01 to 1F. Please refer to rear panel illustration below. CR4001/ 4101/ 4211/ 4002/ 4102/ 4212/ 4003/ 4103/ 4213 Rear panel illustration. AC 12V I/P PARALLEL O/P (DB25F) Switch is ON when pushed up SERIAL O/P (DB9M) SERIAL I/P (DB9F) 18 41 GROUND S2S1 PARALLEL I/P (DB25M) S1 Set security code. (Default Setting: BIT 1,2,3 OFF and BIT 4,5,6,7,8 ON. Security code is 07H) BIT 1 2 3 4 5 6 7 8 Number to be added to the security code if OFF. 1 2 4 8 16 32 64 128 S2 BIT1 ON and BIT2 OFF to receive security code via Pin2 of P4 (DB9F). BIT1 OFF and BIT2 ON* to receive security code via Pin3 of P4 (DB9F). BIT3 OFF and BIT4 ON for dedicated RS-232C. BIT3 ON and BIT4 OFF* for non-dedicated RS-232C. (*denotes factory default setting) CR4004 / 4104 / 4214 1). Open the PC case. Put the metal bracket with power connector into one of the I/O windows. 2). Connect the cable to the HDD type power connector of PC power supply. See illustration below. Then close the PC case. 3). Connect the DB-9 connector to the computer's serial port of COM1 (or COM2). Connect the 4P phone plug connector to the added I/O bracket. See below illustration. 616P PHONE JACK POWER CORD 4 5 CR4005/ 4105/ 4215/ CR4005-II/ 4105-II/ 4215-II 1). Define a drawer number for the cash drawer so that this cash drawer is going to respond accordingly in USB communication. Follow the table below for SWITCH SETTING to adjust the switch S1 according to this drawer number if it is not 7. Please note that within each system there should never be any 2 USB interface cash drawers carrying the same drawer number. Rear View of Model CR4005/4105/ 4215/CR4005-II/ 4105-II/ 4215-II Cash Drawer with USB Interface SWITCH SETTING: Drawer 0 1 2 3 4 5 6 7 SW1 ON OFF ON OFF ON OFF ON OFF SW2 ON ON OFF OFF ON ON OFF OFF SW3 ON ON ON ON OFF OFF OFF OFF SW4 Reserved Default setting: Drawer 7 (SW1: OFF; SW2: OFF; SW3: OFF) 2). Connect USB connector of cable coming out from the rear side of the USB interface cash drawer to USB port of main PC. 3). Check the specification of power adaptor on its nameplate. Insert the power adaptor into the correct power outlet. Insert the output plug to the jack at rear side of CR4005/ 4105/ 4215/ CR4005-II/ 4105-II/ 4215-II to supply power for drawer kickout. 4). Install the USB utility driver from Posiflex Product Information CD with Posiflex POS system or visit our web sites or or for latest updates. Connect to USB Port of Main PC Power Jack of CR4005/4105/4215/ CR4005-II/ 4105-II/ 4215-II USB Connector from CR4005/4105/ 4215/CR4005-II/ 4105-II/ 4215-II 4 3 2 1 O N AC 12V I/P S1 COM1 616P PHONE JACK 4PIN PHONE JACK DB9 UPOS driver application (Applied for all Posiflex cash drawer) Please first find in Posiflex Product Information CDROM or download from Posiflex web sites for UPOS driver setup. In this application CR4XX3 and CR4XX4 respond to openDrawer command only; CR4XX0, CR4XX1 and CR4XX2 are compliant to UPOS version 1.4; CR4XX5 are compliant to UPOS version 1.7 and CR4XX5-II are compliant to UPOS version 1.8. FUNCTIONAL TEST CR4000 / 4100 / 4210 1.Follow the printer’s manual of the printer the cash drawer is connected to open cash drawer. 2.If the cash drawer is connecte...