Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
pg. 66). ... “L-2 SELECT” is set to “SAT” (. pg. 51). . If Just Clock is set to “ON”, the recorder’s clock is automatically adjusted at the start/end of Summer Time. . Just Clock may not function properly depending on the reception condition. 78 EN TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. No power is supplied to the recorder. . The mains power cord is disconnected. Connect the mains power cord. 2. The clock is functioning properly, but the recorder cannot be powered. . “#” is displayed on the front display panel with “AUTO TIMER” set to “OFF”. Press the # button to turn the “#” indicator off. 3. The remote control won’t function. . The batteries are discharged. Replace the dead batteries with new ones. TAPE TRANSPORT SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The tape does not run during recording. . “i” is displayed on the front display panel. Press 4 to turn the “i” indicator off. 2. The tape will not rewind or fast-forward. . The tape is already fully rewound or fast-forwarded. Check the cassette. PLAYBACK SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The playback picture does not appear while the tape is running. . If you are using the RF connection, . . . the TV receiver’s channel selector is not set to the video channel. . . . the recorder’s video channel has not been correctly set. . If you are using the AV or S-VIDEO connection, the TV receiver is not set to the AV mode. If you are using the RF connection, . . . set the TV receiver to the video channel. . . . perform “Video Channel Set” (. pg. 74). If you are using the AV or S-VIDEO connection, set the TV to its AV mode. 2. Noise appears during visual search. . This is normal. 3. Noise appears during normal playback. . The automatic tracking mode is engaged. Try manual tracking. (. pg. 23) 4. The playback picture is blurred or interrupted while TV broadcasts are clear or “USE CLEANING CASSETTE” message appears on the screen. . The video heads may be dirty. Use a dry cleaning cassette TCL-2UX or consult your JVC dealer. 5. Breaks are noticeable in Hi-Fi soundtrack. . The automatic tracking mode is engaged. Try manual tracking. (. pg. 23) EN 79 RECORDING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Recording cannot be started. . There is no cassette loaded, or the cassette loaded has had its record safety tab removed. Insert a cassette, or using adhesive tape, cover the hole where the tab was removed. 2. TV broadcasts cannot be recorded. . “L-1”, “L-2”, “F-1”, “S-1” or “SAT” has been selected as the input mode. Set to the desired channel. 3. Tape-to-tape editing is not possible. . The source (another video recorder, camcorder) has not been properly connected. . All necessary power switches have not been turned on. . The input mode is not correct. Confirm that the source is properly connected. Confirm that all units’ power switches are turned on. Set the input mode to “L-1”, “L-2”, “F-1” or “S-1”. 4. Camcorder recording is not possible. . The camcorder has not been properly connected. . The input mode is not correct. Confirm that the camcorder is properly connected. Set the input mode to “L-1”, “L-2”, “F-1” or “S-1”. TIMER RECORDING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Timer recording won’t work. . The clock and/or the timer have been set incorrectly. . The timer is not engaged. Re-perform the clock and/or timer settings. Press # and confirm that “#” is displayed on the front display panel. 2. Timer programming is not possible. . Timer recording is in progress. Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes. 3. “#” and “[” on the front display panel won’t stop blinking. . The timer is engaged but there’s no cassette loaded. Load a cassette with the record safety tab intact, or cover the hole using adhesive tape. 4. The cassette is automatically ejected, and “#” and “[” on the front display panel won’t stop blinking. . The loaded cassette has had its record safety tab removed. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact. 5. “#” blinks for 10 seconds and the Timer mode is disengaged. . # has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. Check the programmed data and reprogram as necessary, then press # again. 6. The cassette is automatically ejected, the power shuts off and “#” and “[” won’t stop blinking. . The end of the tape was reached during timer recording. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. 7. The SHOWVIEW system does not timer-record properly. . The recorder’s channel positions have been set incorr...