Reflector Tray -shipped in place C. Wire Feeder -inside Reflector Tray D. Instruction Manual - shipped loose II. Position Wire Feeder -refer to Figure 2 A. Pull out Reflector Tray B. Rotate Wire Feeder C. Slide Reflector Tray back D. WARNING: Operating the toaster without the Reflector Tray reduces toasting capabilities. 4 figure 2 WARNING: Genuine APW Wyott Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in APW Wyott equipment. It is essential to use APW Wyott Replacement Parts when repairing APW Wyott equipment. Failure to use APW Wyott Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. CAUTION: Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or it’s contents from accidentally falling, and strong enough to support the weight of the unit and food. WARNING: Failure to provide clearances will cause unit failure and invalidate warranty claims (see installation instructions). 5 III. Toaster Placement A. Locate the toaster near a grounded receptacle of the proper configuration (see below). Plug the cordset directly into receptacle (DO NOTUSE AN EXTENSION CORD). 1. In the United States, NEMA5-15R. 2. In Canada, NEMA5-20R. B. Place the toaster on a flat surface providing the following minimum clearances: 1. Base = one inch (provided with legs installed). 2. Side and back walls = two inch 3. Overhead = Enough space to allow adequate heat displacement. 4. WARNING: Failure to provide these clearances will cause unit failure and invalidate warranty claims. C. Position toaster where customers will not contact any surface labeled "CAUTION HOT". NOTE: DO NOT OPERATE THE TOASTER WITH THE LEGS REMOVED. OPERATION INSTRUCTIONS I. Preparation A. Clean toaster thoroughly before first use (See cleaning instructions). B. Controls Familiarity 1. Top Heat Switch: Operates top elements and conveyor. 2. Bottom Heat Switch: Operates bottom element and conveyor. C. Warm-up time: Allow five (5) minutes. II. Normal Use A. Loading Product 1. Place product on Wire Feeder. The conveyor will automatically draw product through the toaster at a speed determined by conveyor speed control. B. Toasting Darkness: determined by conveyor speed. 1. Darkest toasting - set conveyor speed control to one (1). 2. Lightest toasting - set conveyor speed control to ten (10). SPECIFICATIONS 15.634 2.356 1.000 13.271 14.723 40° 3. Other factors affecting toasting darkness. a) Product moistness -moister product requires slower speeds b) Sugar content in product -product with more sugar requires slower speeds c) Product Temperature -cooler product requires slower speeds 4. For best results, use day old bread stored room temperature. CLEANING INSTRUCTIONS I. Daily Cleaning A. With toaster off and cool, turn toaster on and set conveyor speed to four. B. Using a plastic abrasive pad, wipe the conveyor belt in a back and forth motion (side-to-side) motion to remove baked-on product. Wipe the conveyor belt in the same manner with a hot, damp cloth. C. Turn off toaster. D. Slide the reflector/crumb tray out of toaster by pulling forward. Dispose of crumbs and wash tray in hot, soapy water. Dry tray and place back in toaster. E. Remove toast drawer from toaster by sliding out and lifting up. Dispose of crumbs and wash drawer in hot, soapy water. Wipe crumbs from inside the toaster with a hot, damp cloth. Dry drawer and place back in toaster. F. Wipe the exterior surfaces of the toaster with a hot, damp cloth. II. Periodic Cleaning A. Conveyor Belt 1. Remove conveyor belt from toaster. 2. Use pliers to bend a link to the inside until the hook clears the link above. 3. Repeat on other side. 4. Pull the loosened links together and slide through center of belt link. 5. Clean belt thoroughly (See item 2 under "daily cleaning"). 6. Install conveyor belt by reversing order of steps noted above (See item 1). B. Cooling Intake Fan 1. Unplug and lay toaster on side. 2. Brush dirt and debris from fan opening and guard. 3. WARNING: Neglecting to keep fan opening clean could result in toaster failure. WARRANTY PROCEDURE If warranty service is needed on your AT EXPRESS TM, follow these steps: I. Identify the model and serial number from the rating label on your toaster. II. Consult the enclosed directory, find the service agency nearest you, call the number listed or the 24hour toll free service hot line, 1-800-733-2203. If there is not a service agency listed for your area, the parts distributor will provide service for your toaster. III. To order parts consult the enclosed directory. The parts distributor is listed at the beginning of each state listing. The parts distributors have a complete stock of parts for your toaster. TROUBLESHOOTING I. Always ask and...