Fabricar: ProForm
Tamaño del archivo: 815.72 kb
Nombre del archivo: 475a792a-e92a-470c-b6eb-3269ce8dd2e4.pdf
![en en](/images/flag/s/en.gif)
![]() |
Resumen del manual
1. With the help of a second person, carefully raise the Uprights (82) until the treadmill is in the position shown. 82 1 2. With the help of a second person, carefully lower the 2 treadmill frame to the floor. Remove the Lock Knob (110) from the Lock Pin (114). 110 Make sure that the Lock Pin Collar (112) and the Spring (111) are on the Lock Pin as shown. Insert the Lock Pin into the Latch Bracket (77). Tighten the Lock Knob (110) onto the Lock Pin (114). 112111 114 77 3. Refer to drawing 3a. Press a Handrail Insert (102) into 3b 3a the lower end of a Handrail (85). Hold an Extension Leg (103) against the lower end of the Handrail. Insert a Handrail Bolt (78) with a Handrail Washer (36) into the Extension Leg and thread the Handrail Bolt three or 85 four turns into the Handrail. Notice the angle of the 85 102 103 same angle (see drawing 3b). 103 Handrail and insert the Handrail Bolt and Washer at the Attach a Handrail Insert (102) and an Extension Leg 36 (103) to the other Handrail (85) in the same way. 36 78 78 6 4. Slide the upper end of a Handrail (85) and then the Extension Leg (103) into the right Upright (82) as shown. (Note: It may be helpful to tip the Uprights [82] forward as you insert the Extension Leg. If necessary, tap the Extension Leg with a rubber mallet to fully insert it.) Slide the other Handrail (85) into the left Upright (82) as described above. 5. With the help of a second person, carefully tip the Uprights (82) down as shown. Make sure that the Extension Legs (103) and Handrails (85) remain in the Uprights. Next, attach each Extension Leg (103) with two Screws (101) and a Base Pad (116) as shown in drawing 5. Make sure that the Extension Legs are fully inserted into the Uprights (82) and push down on the Uprights as you tighten the Screws. Note: One replacement Base Pad (116) and Spacer (not shown) are included. If a Base Pad becomes worn and needs to be replaced, use the replacement Base Pad. If a Thick Base Pad (97) needs to be replaced, use the replacement Base Pad with the Spacer. With the help of a second person, carefully tip the Uprights (82) back to the upright position. 6. Refer to drawing 6a. Locate the left Rear Foot (59) on the treadmill. If the left Rear Foot touches the floor, go to step 7. If there is a space between the left Rear Foot and the floor, follow the instructions below. Hold the treadmill firmly with both hands, and raise the treadmill to the storage position as described on page 18. Refer to drawing 6b. Using a phillips screwdriver, remove the Screw (60), the right Rear Foot (59), and the Rear Foot Spacer (114) from the treadmill. Reattach the right Rear Foot without the Rear Foot Spacer. Hold the treadmill with both hands, and lower the treadmill as described on page 19. Check the left Rear Foot (59 [see drawing 6a]). If the left Rear Foot is still off the floor, raise the treadmill and remove the left Rear Foot. Snap the Rear Foot Spacer (122) onto the left Rear Foot and reattach the left Rear Foot. Carefully lower the treadmill. 101 36 78 101 82 36 78 103 103 82 97 85 85 97 82 85 85 82 103 4 5 116 116 97 59 122 60 6a 6b 59 7. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet from damage, place a mat under the treadmill. 7 OPERATION AND ADJUSTMENT THE PERFORMANT LUBETM WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the productNif it will not fit the outlet, have a proper outlet installed by a qualified electrician. Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your homeOs power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right). To purchase a surge suppressor, see your local PROFORM dealer or call 1-800-999-3756 and order part number 146148. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. Th...