Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex keys and your own Phillips screwdriver , adjustable wrench , and wire cuttersmallet . , rubber For help identifying the assembly hardware, see the drawings below. The number in parentheses below each drawing is the key number of the part, from the PART LIST in the center of this manual. The number following the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly. 1/2” Screw (119)–13/4” Tek Screw (58)–81Frame Washer(65)–2Nut (12)–2Frame Bolt (1)–23/4” Screw (3)–6Upright Bolt (4)–4Upright Washer(7)–2Handrail Bolt (9)–4Silver GroundScrew (10)–2ConsoleBolt (2)–2Wheel Spacer(94)–41/4” StarWasher (8)–2Handrail StarWasher (11)–4Upright StarWasher (6)–4L 6 1. Make sure that the power cord is unplugged. Identify the Right Upright (39), which has a square hole in the location shown. Orient the Right Upright (39) and the Base (37) as shown. Attach the Right Upright to the Base with two Upright Bolts (4) and two Upright Star Washers (6); do not tighten the Upright Bolts yet. 2. Orient the Left Upright (38) as shown, and attach it to the Base (37) with two Upright Bolts (4) and two Upright Star Washers (6); do not tighten the Upright Bolts yet. 37 4 6 39 37 38 6 6 Latch Holes 2 1 Square Hole 4 3. Turn the Base (37) over, and set it near the front of the treadmill as shown. Locate the wire in the Right Upright (39). See the inset drawing. Secure the wire to the connector on the Upright Wire (69). Then, insert the connector on the Upright Wire into the square hole in the Right Upright. 3 39 Wire 37 69 Wire 69 7 4. Raise the Uprights (38, 39). See the left inset drawing. Identify the two Frame Spacers (96). Open the included packet of grease, and apply grease to both sides of both Frame Spacers. Next, identify the outer side of each Frame Spacer. Hold a Frame Spacer (96) and a Frame Washer (65) between the Right Upright (39) and the Lift Frame (41), with the outer side of the Frame Spacer facing the Frame Washer and the Right Upright. Attach the Right Upright to the Lift Frame with a Frame Bolt (1), an Upright Washer (7), and a Nut (12); do not tighten the Nut yet. 4 38 39 1 96 65 12 41 7 Outer Side Inner Side 96 1 96 7 12 41 39 65 5. Hold the remaining Frame Spacer (96) and Frame Washer (65) between the Left Upright (38) and the Lift Frame (41), with the outer side of the Frame Spacer facing the Frame Washer and the Left Upright. Attach the Left Upright to the Lift Frame with a Frame Bolt (1), an Upright Washer (7), and a Nut (12); do not tighten the Nut yet. 5 38 1 7 96 65 12 41 96 38 Outer Side 12 1 7 65 Inner Side 96 41 8 39 38 69 9 11 40 9 11 40 7 39 6 69Wire 9 11 40 9 11 40 7 39 6 69Wire 8. Have a second person raise and hold the treadmill Frame (36). Identify the Gas Spring (83). Note that the Gas Spring has a piston end and a cylinder end. See the two small inset drawings. Locate the Spring Clip (90) in the piston end of the Gas Spring. Using your fingernail or the end of a screwdriver, press on the end of the Spring Clip to loosen it, rotate the Spring Clip, and then pull the Spring Clip out of the Gas Spring. Be careful to avoid losing the Spring Clip. Note: Extra Spring Clips are included. Next, hold the piston end of the Gas Spring (83) near the bracket in the center of the Frame (36). Press the end of the Gas Spring as far as possible onto the ball on the bracket. See drawing 8a. Insert the Spring Clip (90) into the two indicated small holes in the piston end of the Gas Spring (83). Then, rotate the Spring Clip until it clips onto the Gas Spring. 9. Pivot the cylinder end of the Gas Spring (83) down to the position shown. Remove the Spring Clip (90) from the end of the Gas Spring. Next, align the cylinder end of the Gas Spring (83) with the bracket in the center of the Base (37). Press the end of the Gas Spring onto the ball on the bracket. Note: It may be necessary to pivot the Frame forward or backward slightly to align the end of the Gas Spring with the ball. See drawing 9a. Insert the Spring Clip (90) into the two indicated small holes in the Gas Spring (83). Then, rotate the Spring Clip until it clips onto the Gas Spring. With the help of a second person, lower the Frame (not shown) to the floor. 83 36 Bracket Cylinder Piston 8 90 9090 90 8336 Bracket 8a Holes 90 83 37 Bracket 9 83 37 Holes 90 9a Bracket 10 10. Attach the ground wire on the Console Base (67) to the right Handrail (40) with a Silver Ground Screw (10). Connect the wire harness on the Console Base (67) to the Upright Wire (69) as shown in the inset drawing. Important: If...