Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
We recommend warm, soapy water. Do not use harsh or abrasive chemicals. 3. Inspect, and tighten all parts before every use. Replace any worn parts immediately. Failure to do so may result in serious injury. 4. Keep children away from the BODYCRAFT GX GYM LEG PRESS at all times. 5. Keep your hands away from cables and pulleys during operation. Keep yo-jr hands away from moving parts other than the designated handles 6. Make certain all cables are seated within the pulleys before every use. 7. Exerrise with care to avoid injury. S. If unsure about the proper use of the BODYCRAITT GX GYM LEG PRESS strength training system call your local BODYCRAFT dealer or our customer service department at Suü-yyu-5556. 1 NO. DESCRIPTION PARTS LIST OTY. 201 BASE STABILIZER 205 MAIN FRAME 203 LEG PRESS SUPPORT 204 SEAT HANDLE 205 SACK PAD ADJUSTER 203 FOOT PLATE 207 RUBBER STOPPER 208 0 25mm AXLE 209 3/4" AXLE 210 COLLAR 211 1-1/4" X 330mm HAND GRIP (p re-assembled) 212 NON SLIP 213 BACK PAD 214 SEAT PAD 215 114mm PULLEY 213 90mm PULLEY 217 LEG PRESS CABLE 218 LOCKING SFRING KNOB 219 SOX 75mm RECT PLUG 220 45mm SQ PLUG 221 SEARING 222 LEG FRESS STOPPER 223 LEG PRESS BUSHING 224 1/2" X 4-1/4" HEX BOLT 225 1/2" X 3-1/4" HEX BOLT 223 1/2" X 1" HEX THREADED BOLT 227 3/3" X 4" HEX BOLT 223 3/8" X 3-1/8" HEX BOLT 229 3/8" X 3' HEX BOLT 230 3/8" X 1-3/4" HEX BOLT 231 3/3'" X 2-3/4" HE X TV! R EAD E D 0 0 LT 232 3/8" if HEX THREADED BOLT 233 3/8" X 5/8' SET SCREW (P re-assembled) 2 3 A 5/13"kpl l-i EX TH READ ED BOLT 235 1/2" WASHER 233 3/8" WASHER 237 1/2" NYLON NUT 238 3/8" NYLON NUT 239 5/1 3' NUT (p re-assembled) 240 SEAT PAD SUPPORT STOPPER 241 CAP FOR NUT 242 3/8" X 3-1/2" HEX BOLT 243 3/4" BUSHING 2 1 1 1 3 1 1 1 1 2 1 2 2 2 4 1 2 1 2 2 2 1 2 11 12 2 3 2 2 4 1 2 4 0 0 207 203 209 210 211 ® © a 221 222 223 224 225 № 226 £= 227 Z=2 228 229 230 23] 232 233 234 t 235 236 m 237 ft 23« 239 240 O m 242 $ 243 h L i 1 t J..J I i ] i 1 i i > I 11 i I iL11 i L ] 1 t L ] 1 0 Ui 1/2 za 1 " ui 1/2 ïrt 2 ” Ui 1/2 ïrt 3 " ui 1/2 '¿a 4" vi 1/2 zu 5" ui 1 n zu 61 (inch) 3 STEP 1 ASSEMBLE BASE FRAME To ease assembly , Do Not tighten ary boits until instmcted, 1 Attach the Base Stabilizer (201) to the Base Frame (1), using wo 1/2"X 3-1/4" Hex Bolts (225), three 1/2" Washers (235) ana one 1/2" Nylon Nut (237) 4 STEP 2 ASSEMBLE MAIN FRAME 1 Attach the Main Frame (202) to The Base Stabilizer (201), using two 1/2" X 4-1/4" Hex Quits (224), four 1/2" Washers (235) and two 1/7 Nylon Nuts (237). 2. insert the 25mm Axle (208) into the Leg Press Subbort (203), then attach to the Main Frame (202) using two Collars (210) {inside tne brackets on the Main Frame (202)}, two Щ X 1" Hex Threaded Bolts (220), and two 1/2= Washers (23^ Tighten the bolts and then cap with two End Caps (241). 3.1 nsert the 3/4' Axle (209) into the top hole in the Leg Press Support (203), then attach the Foot Plate (200) using two 1/2" X 1" Нек Threaded Bolts (220), and tig 1/2" Washers (235) Tighten the boits and then cap with two End Caps (241). 4. Attach Seat Handle (204) to the Main Frame (202), using two 3/0" X 3-1/0' Hex Bolts (22S), four 3/3" Washers (236) and two 3/0' Nuts (230). 5. Attach Seal Pad (21 4) to the M am Frame (202), using two 3/0" X 2-3/4" Нек Threaded Bolts (231) and two 3/0" Washers (230). 6. Attach Back Pad (213) into the Back Pad Adjuster (205), using two 3/8" X 1" Hex Threaded Bolts (232) and two 3/0" Washers (230) Then slide the Back Pad Adjuster (205) to the Main Frame at your desired (213) 5 STEP 3 ASSEMBLE LEG PRESS CABLE Assemble cables and pulleys simultaneousiy. 1. Locate the Floating Pulley Block (21) assembled to the base unit of the GX Unscrew the Floating Pulley Biock (21). Screw the Rubber Stopper (207) into the Top Frame (2) in place of the Floating Puliey Block (21). Flip the Floating Pulley Block (21) over (you 'will need to remove the pulley when doing this) so that the flat end of Floating Pulley Block (21) Is resting against the Rubber Stopper (207) as shown in Fig. 1 2. Screw the threaded end of the Leg Press Cable (217) about half way inlo the threaded receptacle in the Floating Pulley Block (21) This is an adjustment area where the cable can be tightened or loosened. Be certain to always have at least one third of the threaded end of the cable screwed mio the Floating Pulley Block (21). Also be certain to tighten the locking nut securely to prevent the cable from unscrewing. 3 Route the fiat end of 1he cabie down and under the vertical pulley (210) mounted to the Base Stabilizer (201) using one 3/S"X 1-3iA" Hex Bolt (230) and one 3/0" Nylon Nut (238) as shown in Fig. 2 4. Continue routing the cable over to the horizontal Pulley (21S) mounted to the Base Stabilizer (201) using one 3/8" X 1-3/4" Hew Bolt (230) as shown in Fig. 3. 5 Route the cable under a pulley mounted under the seat using two Leg Press Bushings (223), ...