Fabricar: Epic Fitness
Tamaño del archivo: 1.6 mb
Nombre del archivo: a163cf86-033c-a9d4-b181-5fb82aab45d9.pdf
|
Resumen del manual
Then, rotate the Shock Pin until it clips onto the Shock. With the help of a second person, lower the Frame (48) to the floor. 88 102 88 102 7 83 48 Bracket Bracket 7a 8 9 8. Remove the elastic band holding the Upright Wire Harness (75). Have two people hold the console assembly near the Left Upright (73) and the Right Upright (74). Connect the Upright Wire Harness to the console wire. Make sure to connect the connectors properly (see the inset drawing); the connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again to connect them. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the Upright Wire Harness (75) and the console wire into the Right Upright (74). Next, insert the brackets on the console assembly into the Left Upright (73) and the Right Upright. Be careful not to pinch the wires. 74 Console Assembly 73 Bracket Console Wire 75 9. While pressing down on the Handrails (99), attach the console assembly to the Uprights (73, 74) with four Upright Bolts (72), four Washers (78), and four Star Washers (71). Start all four Upright Bolts before tightening them. Note: The Left Accessory Tray (63) and the Right Accessory Tray (64) are replaceable. If these parts become dislodged from the console assembly, simply press them back in. 9 8 75 Console Assembly 72 64 78 71 73 78 99 99 63 71 74 Collar Spring 99 Knob Pin 10. Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Next, insert the pin into the hole in the side of the Handrail (99). Then, tighten the knob back onto the pin. 10 11. Place the treadmill in the storage position (see HOW TO FOLD THE TREADMILL FOR STORAGE on page 23). Center the Frame (48) between the Uprights (73, 74). Tighten the Upright Bolts (72) in the lower ends of the Uprights (73, 74). 73 11 74 48 72 72 12. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrench in a secure place; the allen wrench is used to adjust the walking belt (see page 26). To protect the floor or carpet, place a mat under the treadmill. If you purchase the optional chest pulse sensor (see page 22), follow the steps below to install the receiver included with the chest pulse sensor. 1. Make sure that the power cord is unplugged. Remove the indicated Screw (67) and the Access Door (70) from the left side of the Console Back (69). 2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Back (69). Hold the receiver so the small cylinder is oriented as shown. Attach the receiver to the plastic posts on the Access Door (70) with the two included small screws. 3. Make sure that no wires are pinched. Reattach the Access Door (70) with the Screw (67). The other wires included with the receiver may be discarded. A 70 69 Small Cylinder 67 Wire Small Screws 10 TREADMILL OPERATION THE PRE-LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD tric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets. This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illus used to connect the surge suppressor to a 2-pole DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or service- man if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician. 2 Grounded Outlet Box Grounding Plug Surge Suppressor Surge Suppressor Grounding Pin Adapter Lug Metal Screw Grounded Outlet Grounding Pin Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right). To purchase a surge suppressor, see your local EPIC dealer or call the toll-free telephone number on the f...