Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
The PROSPOTfitness® P-600 has a footprint of approximately 6’x 6’. The barbell is approximately 7’ long. Locate your PROSPOTfitness® P-600 away from any source of water. Do not allow any liquid to be near the machine or spilled on any electrical part. Do not insert any object into the electrical box. • Approximate assembly time is 1-1/2 hours. • A flat area of 9’ x 9’ will be required to assemble and properly use the PROSPOTfitness® P-600. • You will need the following tools and a helper to complete the assembly: • Enclosed you will find the following tools: • 3 mm Allen Wrench • 4 mm Allen Wrench • 6 mm Allen Wrench • 3/16" Allen Wrench • 9/16" Allen Wrench • You will need the following tools: • 16 mm Hex Head Wrench • 18 mm Hex Head Wrench • Philips Screw Driver • Floor Padding, such as cardboard, to avoid scratching your floor during assembly. • A good pair of scissors will be helpful in separating the parts from one another while removing them from the cartons. • HAND TIGHTEN all bolts. DO NOT fully tighten bolts until instructed to do so. • Assistance by a second person is recommended for some steps of this assembly. • Before assembly, separate and identify the right-sided parts from the left-sided parts. These parts are easily distinguished by the manner in which the pre-drilled holes align with corresponding parts, or are identified by “L“ & “R” stickers. • The PROSPOTfitness® P-600 uses several different lengths of bolts. Be careful to use the correct length of bolt called for at each step of assembly. Refer to the sizing charts provided. • WARNING: Never perform any maintenance on the ProSpotfitness® P-600 while the Power Supply is plugged into the wall !!! ALWAYS REMEMBER: After the initial set up of the system or after performing any service on the unit, RESET the Computer on your ProSpot system before using it. Just unplug the power supply from the Electronic Box, wait 30 seconds and plug back in. Resetting the Computer allows it to recalibrate and work to its greatest efficiency. --2- Instructions for Assembly of the ProSpotfitness® P-600 Step #1 MAIN FRAME ASSEMBLY 1. Place the Base Rails (6,7) opposite each other in the center of the assembly area as shown in the illustration. Place Lower Frame Cross Brace (14) between the two Base Rails (6,7) so that the side, pre-drilled holes of the Base Rails align with the holes of the Lower Frame Cross Brace. Secure with bolt #107, flat washer #133 and lock nut #128. 2. Place the Lower Back Base Rail (13) between the two Base Rails (6,7). Make sure the rubber grommet hole for the Base Frame Wire Harness (143) is facing toward the back of unit. Thread the Base Frame Wire Harness (143) sticking out of the ends of the Lower Back Base Rail (13) through the side openings of the side Base Rails (6,7). Note: The optional ProSpotfitness® PHL-60 Hi/Low Pull can be mounted rear- facing in order to create a separate exercise station. If you wish you to mount the PHL-60 rear-facing, make sure the rubber grommet hole for the Base Frame Wire Harness (143) is facing toward the front of the unit when placing the Back Base Rail (13) between the two Base Rails (6,7). 3. Align the side pre-drilled holes of the Base Rails (6,7) with the holes of the Lower Back Base Rails (13). Place right and left rear locking posts (one at a time) (4,5) onto Base Rails (6,7) by lining up holes with the Base Rails. Ensure that holes are facing the back. Secure with bolts #106, flat washers #133 and lock nuts #128. Plug Base Rail Wire Harness (143) into Spiral Cable (144) as shown in Diagram. 4. Place right and left Front Guide Posts (1,2) onto Base Rails (one at a time) (6,7) by lining up holes with the Base Rails (6,7). Make sure decals and pulleys are facing forward. Attach Support Plate (3) to inside of both right and left Guide Posts (1,2) to the Base Rails. Secure with bolts # 106, flat washers #133 and lock nuts #128. 5. Slide the right and left Cable Head Slider Frame (15,16) onto right and left Front Guide Posts (1,2) so that the Lock Down Pin (26) on each Cable Head Slider Frame is on the inside on the Front Guide Posts (1,2). Install Lock Down Pin (26) by screwing it into the pre-threaded hole. 6. Attach upper Support Plate (3) to outside of both right and left Front Guide Posts (1,2). Insert two bolts #106 and two flat washers #133 through two lower holes in the upper Support Plate (3). Align the holes of the Front Top Rail (12) with the holes of the right and left Front Guide Posts (1,2). Secure with bolts #106, flat washers #133 lock nuts #128. 7. Attach Back Top Upright Support Plate (10) to the outside of both right and left Rear Locking Posts (4,5). (Note: Pre-drilled holes of the Back Top Upright Support Plates are placed off center. To ensure proper placement, position Back Top Upright Support Plate so that the holes are toward the front of the Rear Locking Posts (4,5). (See diagram.) Insert two bolts #106 and two flat washers #133 through two lower holes in the Back Top ...