Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The PROSPOTfitness® HG-5 has a footprint of approximately 8’x 8’. The surface should be level and even. The barbell is approximately 7’ long. Locate your PROSPOTfitness® HG-5 away from any source of water. Do not allow any liquid to be near the machine or spilled on any electrical part. Do not insert any object into the electrical box. • This unit uses standard 110-volt household current. Since there are two Power Adapters for this unit we recommend using a Surge Protector Plug Strip to protect and extend the life of the power supplies and the Electronic Box from power surges and lightening strikes. The Neon Lighting System does not have an on/off switch. Lights come on when Power supply is plugged into plug strip. A Surge Suppressor Plug strip with a switch will allow shutting Lights off when unit is not in use. A flashing green light will appear on the Electronic Box when power is on. When sensors are activated, a steady red light will also come on. • The HG-5 unit is designed for climate controlled environments (indoor use only). Outdoor or non-climate controlled use may affect the proper function of HG-6 and will void the warranty. • Assembly time is approximate 2 hours. • A flat area of 8’ x 8’ will be required to assemble and properly use the PROSPOTfitness® HG-5. • You will need the following tools and a helper to complete the assembly: • 4 mm Allen Wrench • 5 mm Allen Wrench • 17 mm (11/16”) Hex Head Wrench • 19 mm (3/4”) Hex Head Wrench • Adjustable wrench • Metric Socket Set • Philips Screw Driver • Pliers • Scissors and or Razor knife • Floor Padding, such as cardboard, to avoid scratching your floor during assembly. • Carefully remove parts from packaging. A good pair of scissors will be helpful in separating the parts from one another while removing them from the cartons. Be careful not to cut or damage parts with scissors or razor knife. Remove all parts from packing. Make sure there are no small parts left in boxes. Do not discard boxes until assembly is complete. • Before assembly, separate and identify the right-sided parts from the left-sided parts. These parts are easily distinguished by the manner in which the pre-drilled holes align with corresponding parts, or are identified by “L“ & “R” stickers. Left and right are determined by facing the unit. Not the user’s perspective. • The PROSPOTfitness® HG-5 uses several different lengths of bolts. All fasteners come in labeled Blister Packs by part number. Be careful to use the correct length of bolt called for at each step of assembly. Do not remove fasteners from Blister packs until part is needed. • Note some parts mat come preassembled with fasteners. • HAND TIGHTEN all bolts. DO NOT fully tighten bolts until instructed to do so. • Assistance by a second person is recommended for some steps of this assembly. • WARNING: Never perform any maintenance on the ProSpotfitness® HG-5 while the Power Supply is plugged into the wall !!! ALWAYS REMEMBER: After the initial set up of the system or after performing any service on the unit, RESET the Computer on your ProSpot system before using it. Just unplug the power supply from the Electronic Box, wait 30 seconds and plug back in. Resetting the Computer allows it to recalibrate and work to its greatest efficiency. Instructions for Assembly of the ProSpotfitness® HG-5 Step #1 MAIN FRAME ASSEMBLY 1. Referencing Diagrams 1 & 2, find the part Front Cross Brace (3). The Wire Harness (108) that runs thru this part. This may be packed in this Cross Brace to prevent damage. Pull on ties and harnesses so that connector ends hang loose out of access holes. Be careful not to pull too hard and remove or damage the wire harnesses. 2. Now place the Rear Bottom Panel (5) in center of the assembly area. Next place the Right and Left Base Rails (1, 2) opposite each other on each side of the Rear Bottom Panel. Note the 7/8” access holes for wiring on side of Right and Left Base Rails (1, 2) should face inward. Now position the Front Plastic Bottom Panel (4) (Remove paper cover on plastic) in front of the Rear Bottom Panel (5) between the Base Rails. Insert Bolts (74) thru the Backing Plate (158) and attach the Side Rails (1 & 2) to the Rear Bottom Panel using M12 x105 Bolts (74), M12 Washers (72) & M12 Nuts (73). Do not fully tighten bolts at this time. 3. Now place the Front Cross Brace (3) between rails so that the access holes with the harnesses hanging out on the end of the Rear Cross Brace (3) align with the holes of the Base rails (1 & 2). Make sure the wire harness that comes out of the middle of the Front Cross Brace (3) faces toward the back of the unit. Refer to Diagrams 1 & 2. 4. Next feed the two Wire Harnesses (108) thru the access holes in the Right and Left Base Rails (1 & 2). Pull up thru the round hole in the Right and Left Base Rails (1 & 2). Insert M12*105 Bolts (74) thru the Backing Plate with Panel Hook (69) and attach the Side Rails (1 & 2) to the Front Cross Brace using M12 Washers (72) & M12 N...