Votos - , Puntuación media: ( )

Manual de usuario Healthrider, modelo DT1000 831.288261

Fabricar: Healthrider
Tamaño del archivo: 538.88 kb
Nombre del archivo: 83aa5054-99c3-43c0-bad2-af17eb44069f.pdf

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

Locate the battery compartment on the back of the Monitor. Insert two batteries into the Monitor. Make sure that the negative ends of the batteries (marked O.O) are touching the springs in the Monitor. Close the battery cover. 6. Thread the wire on the Electronic Monitor (19) through the hole in the middle of the Monitor Bracket (61). Attach the Electronic Monitor (19) to the Monitor Bracket with four Monitor Screws (59). Connect the Sensor Wire (47) to the wire on the Electronic Monitor (19). Attach the Monitor Bracket (61) to the Frame (46) using two M4 x 12.5mm Tek Screws (60). Make sure that the Sensor Wire is not pinched between the Monitor and the Frame. 7. Apply a small amount of grease to the bolt welded in the Right Handlebar (38). Connect a Link Arm (26) to the lower end of the Right Handlebar with a Brass Handlebar Bushing (27), an M8 Washer (43), and an 8mm Locknut (36) as shown. Attach the other Link Arm to the Left Handlebar in the same manner (not shown). 5 Batteries 19 6 47 Monitor Wire 59 46 59 19 61 60 7 26 36 43 27 38 8. Note: Apply a small amount of grease to all of the small parts assembled in this step. Slide a 13mm Washer (23) onto the indicated end of a Pedal Axle (24). Insert the Pedal Axle into the right Link Arm (26). Slide a Steel Link Arm Bushing (32), a 13mm Washer (23), and a Pedal Spacer (33) onto the Pedal Axle. Firmly tighten the Pedal Axle clockwise into the right arm of the Crank (39). Tighten a 1/2O Locknut (22) onto the Pedal Axle. Attach the other Pedal to the left arm of the Crank (not shown) in the same manner. 9. Make sure that all parts of the exercise bike are properly tightened. 11 24 23 26 32 23 33 39 22 8 5 HOW TO USE THE LIFESTYLER. DT1000 SEAT ADJUSTMENT As you pedal, there should be a slight bend in your knees when the pedals are at the lowest position. To adjust the seat, first hold the seat and unscrew the seat knob. Align one of the holes in the seat post with the hole in the frame. Insert the seat knob into the frame and the seat post, and tighten the seat knob into the frame. Make sure to insert the seat knob through one of the holes in the seat post; do not insert the seat knob under the seat post. Seat Seat Post Frame Seat Knob LEVELING THE LIFESTYLER. DT1000 If the exercise bike does not rest evenly on the floor, the problem may be corrected with the adjustable caps on the front stabilizer. Rotate one or both caps until the exercise bike rests evenly on the floor. Front Stabilizer Adjustable Cap DESCRIPTION OF THE ELECTRONIC MONITOR The electronic monitor features five modes that provide instant exercise feedback during your workouts. The modes are described below. . SpeedNDisplays your pedaling speed, in miles per hour. . TimeNDisplays the length of time you have exercised. Note: If you stop pedaling for ten seconds or longer, the time mode will pause until you resume. . DistanceNDisplays the total distance you have pedaled, in miles. . CalorieNDisplays the approximate number of Calories ...