Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Item Qty Description R1 R3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2 10 5 8 8 0 1 1 1 1 2 4 2 5 2 4 8 4 0 2 10 5 8 8 4 1 1 1 1 2 2 2 5 2 4 8 4 4 50 mm Button Head Screw Button Head Screw - 18 mm O.D. 55 mm Phillips Screw Lock Washer - 12.2 mm O.D. 8 mm Phillips Screw 40 mm Button Head Screw with Locking Compound Flat Washer - 24 mm O.D. Rubber Bumper 12 mm Phillips Screw with Locking Compound Phillips Screw Hex Head Bolt Thick Flat Washer - 16 mm O.D. mm Hex Head Bolt Small Head Phillips Screw Flat Washer - 12 mm O.D. 12 mm Self Tapping Screw 12mm Phillips Screw 15 mm Flat Washer Rubber Bumper Insert 1” 12 mm Large Head 100 mm 60 12 mm 1) 2) 4) 5) 7) 13) 14) 15) 16) 17) 18) 8) 9) 10) 11) 12) 3) Slide the MONOCOLUMN (S) into the MONOCOLUMN BRACKET (Z). Slide the MONOCOLUMN down until it is fully seated. Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two 100 mm HEX HEAD BOLTS (13) and three THICK FLAT WASHERS (14) (as shown) from the front side of the MONOCOLUMN and two 60 mm HEX HEAD BOLTS (15) and THICK FLAT WASHERS (14) from the user left side of the MONOCOLUMN BRACKET. Tighten the BOLTS securely. Be careful not to pinch the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) when inserting the MONOCOLUMN (S) into the MONOCOLUMN BRACKET. Connect the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) to the corresponding WIRE (W) from the SIDE ACCESS HOLE (X) of the MONOCOLUMN. Slide the MONOCOLUMN COVER (T) downward to meet the MAIN SHROUDS. Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 12 mm PHILLIPS SCREWS (16). Tighten the SCREWS securely. Do not overtighten the SCREWS. Attach the RIGHT (BB) and LEFT (CC) FRONT HANDLEBARS (labeled right and left) to the MONOCOLUMN as shown using two each 15 mm BUTTON HEAD SCREWS (2). Tighten the SCREWS securely. Remove the DISPLAY CONSOLE (DD) from its shipping carton. Position the DISPLAY CONSOLE above the DISPLAY CONSOLE BRACKET (EE). Connect the CONSOLE WIRE (FF), HEART RATE WIRE (GG) (RED), and GROUND WIRE (HH) (GREEN) to the corresponding JACKS located on the back of the DISPLAY CONSOLE. Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET using four 12 mm PHILLIPS SCREWS (18). Tighten the SCREWS securely. Do not overtighten the SCREWS. PEDAL STRAP PEDAL STRAP PEDAL PEDAL PEDAL STRAP PEDAL STRAP PEDAL PEDAL STRAP Position the unit in the desired location for use. The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers. Level the unit before use. Refer to the leveling instructions stated in the User Manual. CAUTION: 5. 6. NOTE: NOTE: Locate the RIGHT PEDAL (JJ) (marked with an "R") and PEDAL STRAP (KK) (marked with an "R"). With the side of the marked with an “R” facing upward, slide the slotted end of the through the left slot in the . Fasten one of the slots onto the tab located under the left slot of the . Bend the upward and slide the remaining end of the through the right slot in the and into the strap adjustment clip. The should securely engage the strap adjustment clip. Install the RIGHT PEDAL (JJ) to the USER RIGHT CRANK ARM (LL). Repeat for the LEFT PEDAL (marked with an "L") and PEDAL STRAP (marked with an "L"). The LEFT PEDAL has reverse threads. Pedals need to be securely tightened or clicking may occur. 7. Locate the WATER BOTTLE BRACKET (MM). Secure the WATER BOTTLE BRACKET to the underside of the MONOCOLUMN (S) using two 12 mm PHILLIPS SCREWS (12). Tighten the SCREWS securely. Insert the WATER BOTTLE (NN) into the WATER BOTTLE BRACKET. R1 Only: 12 S MM NN 2) 6) 12) 16 17 Y W S 14 AA 14 13 Z EE DD 15 BB V T HH FF GG 18 X 2 CC 2) H E G 3 G 5 2 J F 4 O K 6 11 7 3 9 8 10 L N M U O 12 P R Q F 4 5 19 JJ Assembly Guide: Look for the number coded hardware bags that match the assembly sequence. 19) GG FF Physical Dimensions: Length: Width: Height: Weight: 56.5 inches / 143.5 centimeters 25.75 inches / 65.4 centimeters 54 inches / 137 centimeters 147 pounds / 67 kilograms 56.5 inches / 143.5 centimeters 25.75 inches / 65.4 centimeters 54 inches / 137 centimeters 147 pounds / 67 kilograms Length: Width: Height: Weight: R1 R3 HH ...
Otros modelos de este manual:Formadores - R1 (3.87 mb)