Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
8. Make sure all spring loaded pull pins are fully engaged in the adjustment position and fully tighten thumbscrew before use. 9. Children must not be allowed near this machine. Supervise teenagers. . NOTE: In a continual effort to improve our products, specifications are subject to change © 2001 Life Fitness, a division of Brunswick Corporation. All rights reserved. ParaBody is a trademark of Brunswick Corporation 2 IMPORTANT NOTES Please note: * Thank you for purchasing the ParaBody 874 Multi-Angle Bench System. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. Tools Required for Assembly * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * Adjustable wrench * Tape measure Bolt Length Ruler NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT. BOLT LENGTH BOLT LENGTH RULER: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 3 1’ 2’3’ 4’5’ 1’ 7’ 6’ 5’ 4’ 3’ 2’ 1 Square = 1’ X 1’ 4 PARTS LIST PART # LEA6650609 LEA6650109 LEA6649309 LEA6624210 LEA6624310 LEA6259109 LEA6655709 LEA6654521 LEA6654421 LEA6406401 LEA6412001 LEA6236701 LEA6692601 LEA6405201 LEA7234801 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QTY 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 PART # LEA6145801 LEA3235204 LEA3235212 LEA3114403 LEA3114702 LEA3235315 LEA3235322 LEA3235432 LEA3235501 LEA3221705 LEA6417801 LEA6650201 LEA6416601 LEA7339801 DESCRIPTION THUMBSCREW 3/8 X 1” BOLT 3/8 X 3” BOLT 3/8” WASHER 3/8” LOCK NUT 1/2 X 3-3/4” BOLT 1/2 X 5-1/2” BOLT 1/2 X 8” BOLT 1/2” LOW HEIGHT LOCK NUT 1/2” E-RING 1/2 X 1” SPRING 1/2” FLANGE SPACER 1-1/2 X 3/4” GLIDE (8 PER) 1/2” DIA U-PIN QTY 1 6 4 14 4 1 1 1 3 1 1 2 1 1 DESCRIPTION BENCH FRAME ADJUSTABLE SLIDE ADJUSTABLE SLEEVE LEFT BACK PAD ANGLE RIGHT BACK PAD ANGLE FRONT BASE REAR BASE SEAT PAD BACK PAD HINGE TAB SPRING PIN ASSEMBLY 1-3/4” SQ. END CAP 3 X 2” END CAP 2” SQ. END CAP 2” SQ. COVER CAP KEY 16 17 18 19 20 21 22 23 24 25 26 27 28 29 FIGURE 1 1 16 29 25 26 PARTS LIST PART # LEA6650609 LEA6650109 LEA6649309 LEA6624210 LEA6624310 LEA6259109 LEA6655709 LEA6654521 LEA6654421 LEA6406401 LEA6412001 LEA6236701 LEA6692601 LEA6405201 LEA7234801 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QTY 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 PART # LEA6145801 LEA3235204 LEA3235212 LEA3114403 LEA3114702 LEA3235315 LEA3235322 LEA3235432 LEA3235501 LEA3221705 LEA6417801 LEA6650201 LEA6416601 LEA7339801 DESCRIPTION THUMBSCREW 3/8 X 1” BOLT 3/8 X 3” BOLT 3/8” WASHER 3/8” LOCK NUT 1/2 X 3-3/4” BOLT 1/2 X 5-1/2” BOLT 1/2 X 8” BOLT 1/2” LOW HEIGHT LOCK NUT 1/2” E-RING 1/2 X 1” SPRING 1/2” FLANGE SPACER 1-1/2 X 3/4” GLIDE (8 PER) 1/2” DIA U-PIN QTY 1 6 4 14 4 1 1 1 3 1 1 2 1 1 DESCRIPTION BENCH FRAME ADJUSTABLE SLIDE ADJUSTABLE SLEEVE LEFT BACK PAD ANGLE RIGHT BACK PAD ANGLE FRONT BASE REAR BASE SEAT PAD BACK PAD HINGE TAB SPRING PIN ASSEMBLY 1-3/4” SQ. END CAP 3 X 2” END CAP 2” SQ. END CAP 2” SQ. COVER CAP KEY 16 17 18 19 20 21 22 23 24 25 26 27 28 29 FIGURE 1 1 16 29 25 26 STEP 1: • Assemble the 1/2” DIA. U-PIN (29) to the BENCH FRAME (1) using one 1/2 X 1” SPRING (26), and one 1/2” E-RING (25) as shown in FIGURE 1. • Thread one THUMBSCREW (16) into the BENCH FRAME (1) as shown in FIGURE 1. The THUMBSCREW (16) will be used to tighten down attachments. 5 6 FIGURE 2 STEP 2: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the FRONT BASE (6) to the BENCH FRAME (1) using two 3/8 X 3” BOLTS (18), four 3/8” WASHERS (19), and two 3/8” LOCK NUTS (20). See FIGURE 2. • Slide four 2” SQ. COVER CAPS (15) over the ends of the FRONT & REAR BASE (6 & 7) as shown in FIGURE 2. 1 6 20 19 19 15 7 19 20 15 19 18 3/8 X 3” 18 3/8 X 3” • SECURELY assemble the REAR BASE (7) to the BENCH FRAME (1) using two 3/8 X 3” BOLTS (18), four 3/8” WASHERS (19), and two 3/8” LOCK NUTS (20). See FIGURE 2. 7 STEP 3: FIGURE 3 • Insert one 1-3/4” END CAP (12) into the end of the ADJUSTABLE SLIDE (2) as shown in FIGURE 3. • Attach eight 3/4 X 1-1/2” GLIDES (28) to the inside of the ADJUSTABLE SLEEVE (3) as shown in FIGURE 3 using the following steps: • Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (28) are to be attached. • Remove the 3/4 X 1-1/2” GLIDES (28) from the paper backing and firmly apply them to all shown surfaces. • SECURELY assemble one SPRING PIN ASSEMBLY (11) to the spring pin barrel on the ADJUSTABLE SLEEVE (3). See FIGURE 3. • Pull back on the SPRING PIN (11) and CAREFULLY insert the ADJUSTABLE SLIDE (2) into the ADJUSTABLE SLEEVE (3) as shown in FIGURE 3. • Assemble the ADUSTABLE SLEEVE (3) to the BENCH FRAME (1) using one 1/2 X 3-3/4” BOLT (21), two 1/2” FLANGE SPACERS (27), and one 1/2” LOW HEIGHT LOCK NUT (24) as shown in FIGURE 3. 1/2 X 3-3/4” 21 24 1/2” LOW HEIGHT 27 27 11 2 28 12 1 3 8 STEP...