Votos - 2, Puntuación media: 4.5 ( )

Fabricar: Life Fitness Tamaño del archivo: 698.11 kb Nombre del archivo: b2f3373b-e8fa-4dd0-9a54-b1cf8c871470.pdf Idioma del manual:

Padded Seat Upper Pedals Seat Knob (Behind Sideshield) Lower Pedal Monitor Weight Tube Weight Collar Weight Center Post 3 ASSEMBLY Before beginning assembly, carefully read the • Tighten all parts as you assemble them, unless following information and instructions: instructed to do otherwise. • Assembly requires two persons. • During assembly, make sure that all parts are oriented as shown in the drawings. • Place all parts in a cleared area and remove the packing materials; do not dispose of the packing THE FOLLOWING TOOLS (NOT INCLUDED) materials until assembly is completed. ARE REQUIRED FOR ASSEMBLY: • Read each assembly step before you begin. • Two (2) adjustable wrenches • To identify the small parts used in assembly, use • Lubricant, such as petroleum jelly or grease, the part identification chart below. The num-will also be required. ber in parenthesis below each part refers to the key number of the part. The second number Assembly will be more convenient if you have the refers to the quantity needed for assembly. Note: following tools: A socket set, a set of open-end or Some parts may have been pre-attached for closed-end wrenches, and a rubber mallet. shipping purposes. If a part is not in the parts bag, check to see if it has been pre-attached. Rubber Washer (51)–4 Frame Axle (13)–2 (External Thread) M6 Hex Nut (54)–4 M8 Nylon Jam Nut (7)–2 M6 Flat Washer (55)–4 M8 x 1.375” Bolt (17)–1M6 x 60mm Bolt (53)–4 Plastic Washer (49)–2 M8 x 120mm Bolt (57)–1 Axle Fastener (56)–4 (either Bolts or Acorn Nuts) OR Frame Axle (13)–2 (Internal Thread) 4 5 1. Before beginning assembly, make sure that you have read and understand the information on page 4. Attach one of the Stabilizers (31) to the Main Frame (1) with two M6 x 60mm Bolts (53), two M6 Flat Washers (55), and two M6 Hex Nuts (54). 1 31 54 55 53 1 1 45 58 58 45 45 34 54 55 1 31 53 2. Attach the other Stabilizer (31) to the Main Frame (1) with two M6 x 60mm Bolts (53), two M6 Flat Washers (55), and two M6 Hex Nuts (54). 3. Attach the Front Cover Panel (34) to the Main Frame (1) using four Fastener Bases (45) and four Fastener Pins (58). First, insert the Fastener Bases through the Cover Panel and into the Main Frame. Next, push a Fastener Pin (58) into the hole in each Fastener Base until it is flush with the Base. 4. Lubricate an Frame Axle (13). Attach the Handlebar Swing Arm (5) to the Main Frame (1) with the Frame Axle, two Rubber Washers (51), and two Axle Fasteners (56). Note: If the ends of the Frame Axles (13) are internally threaded, the Axle Fasteners (56) will be bolts; if the ends are externally threaded, the Axle Fasteners will be acorn nuts (see the PART IDENTIFICATION CHART on page 4). 4 3 1 56 51 51 56 5 Lubricate—13 2 6 7 45 45 58 58 2 21 49 10 7 11 17 5 5 6 51 56 36 Hole 1 4 51 5. Push the Magnet Bracket (36) into the hole in the Pedal Frame (4). Lubricate an Frame Axle (13). Attach the Pedal Frame (4) to the Main Frame (1) with the Frame Axle (13), two Rubber Washers (51),...

Descargar ahora

Introduzca dos números de la imagen: