Votos - 1, Puntuación media: 3
(
)
)
|
Fotos y especificaciones Life Fitness 91Ti |
Resumen del manual
A temporary adapter MUST NOT BE USED to connect this plug to a two-pole receptacle in North America. If a properly grounded, 20-amp outlet is not available, one must be installed by a qualified electrician. Models drawing 16 amps or more must be installed on a dedicated line. IL EST ABSOLUMENT INTERDIT d'employer un adaptateur temporaire pour brancher cette fiche sur une prise a deux poles en Amerique du Nord. Si aucune prise de 20 A correctement mise a la terre n'est disponible, il convient d'en faire installer une par un electricien qualifie. Les modeles utilisant 16 A ou plus doivent etre installes sur des lignes qui leur sont reservees. DANGER: A risk of electrical shock may result from improper connection of the equipment- grounding conductor. Check with a qualified electrician if in doubt as to proper grounding technique. DO NOT modify the plug provided with the product. If it will not fit an electrical outlet, have a proper outlet installed by a qualified electrician. DANGER: Un branchement incorrect du conducteur de mise a la terre peut entrainer des risques de decharge electrique. Consultez un electricien si des doutes subsistent quant a la technique de mise a la terre. NE MODIFIEZ PAS la fiche fournie avec l'appareil. Si elle ne s'adapte pas a une prise, faites en installer une correcte par un electricien qualifie. 10 REMOVING AND REPLACING THE WAX BAG The wax lubrication system is a standard feature on the 91Ti model and international 90T model. Treadmills with waxers are equipped to monitor wax levels automatically. On the 91Ti, when the the wax bag is six-percent full, the console displays “NOTIFY MAINTENANCE -- WAXER NEEDS REFILL”. When the bag is empty, the treadmill shuts down, and the console displays, “NOTIFY MAINTENANCE -- WAXER EMPTY”. On a waxer-equipped 90T model, when the wax bag is sixpercent full, the DATA DISPLAY windows show “Err9”. When the wax bag is empty, the treadmill shuts down and the DATA DISPLAY windows show, “Err10”. The wax bag is installed underneath the motor pan of the treadmill. To make replacing the bag as easy as possible, use the UP LEVEL ARROW key to elevate the treadmill to the 15 percent incline. Before starting the procedure, turn the power off (“I”) at the ON/OFF switch, and unplug the unit from the electrical outlet. Open the wax tray: Pull out the three push rivets (A) that fasten the front edge of the wax tray (B) to the bottom of the motor pan (C). If necessary, use a flat-edge screw driver to pry off the rivets. The rivets are reusable. Set down the front edge of the wax tray with the wax bag on top of it. Note: The rear edge of the wax tray is attached to the motor pan during factory assembly. Detach the old wax bag: Remove the motor cover. Engage (1) the wax bag hose clamp (D) to prevent any wax residue from seeping out of the bag. Then, gently work the wax bag hose off of the barbed nozzle on the wax pump inlet hose located inside the motor compartment. Open (2) the hose clamp, and slide it off. Discard the old wax bag. Attach the hose clamp to the new wax bag: Slide the hose clamp (D) over the end of the new wax bag outlet hose (E). Position the clamp approximately three inches from the end of the hose and clamp it (1) onto the wax bag hose to prevent spillage. Position the wax bag under the frame: Place the wax bag (F) on top of the wax tray, so that the wax bag is directly underneath the treadmill motor pan (C), the wax bag flange is facing out toward the front of the treadmill, and the wax bag hose is near the hole (G) at the bottom of the motor pan through which the hose will be fed in the next step. Connect the wax bag hose to the pump inlet hose: Cut off the end of the wax bag hose (E) one half-inch from the end. Feed the hose through the hole (G) at the bottom of the motor pan, and slide it onto the barbed nozzle on the wax pump inlet hose located inside the motor compartment. Be sure to fully seat the wax bag hose onto the inlet hose. Release (2) the hose clamp (D). CAUTION: Failure to release the hose clamp greatly shortens belt life. MISE EN GARDE : la bride de serrage doit etre relachee sous peine de reduire de facon importante la duree de vie du tapis. Close the wax tray: Align two holes of the wax bag flange with the two holes along the front edge of the wax tray (B) and the two holes at the bottom of the treadmill motor pan (C). Attach the wax tray and wax bag (F) to the motor pan with two of the push-rivets (A), simply by pushing each rivet upward through both sets of aligned holes. Once each rivet is pushed through the holes as far as possible, its front tip flares open to keep the tray and wax bag fastened to the motor pan. Push a third push-rivet through the remaining aligned holes in the wax tray and the bottom of the treadmill motor pan. Inform the system that a new wax bag has been installed: Access the Manager’s Configuration. For details, see Section 5.1, titled Entering and Using the Manager’s Configuration. On the 91Ti model...
Otros modelos de este manual:Formadores - 90T (839.79 kb)