Votos - , Puntuación media:
(
)
)
Fabricar: Life Fitness
Tamaño del archivo: 642.96 kb
Nombre del archivo: 37c3c0bc-c1f3-423e-9212-b425d65bb082.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
MISE EN GARDE : VEILLEZ A NE PAS PINCER LE FAISCEAU (C). 3. Align and insert the HANDLEBAR ASSEMBLY (#15) into THE HANDLEBAR BRACKET TUBE (F) as shown until the mounting holes in the HANDLEBAR ASSEMBLY align with those of the HANDLEBAR BRACKET TUBE. Model 93S Shown 14 15 F 10 13 6 J 19 8 15 F 8 16 4. (Model 93S / 90S International) Locate the TELEMETRY CABLE (#17). Feed the 3-PIN CONNECTOR (3P) end of the cable through the front of the HANDLEBAR ASSEMBLY (#15). The cable must be routed down the HANDLEBAR BRACKET TUBE (F) and back up the top of the MONOCOLUMN (#10). Feed the 3-PIN CONNECTOR through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. 5. (Model 93S) Align the USER LEFT BULLHORN (#13) to the HANDLEBAR BRACKET TUBE (F). Using three MOUNTING SCREWS (#6), secure the USER LEFT BULLHORN to the HANDLEBAR BRACKET TUBE and the HANDLEBAR (#15). Tighten the SCREWS securely. Repeat the procedure for the USER RIGHT BULLHORN (#14). (Model 90S) Secure the HANDLEBAR ASSEMBLY (#15) to the HANDLEBAR BRACKET TUBE (F) using six MOUNTING SCREWS (#4). Tighten the SCREWS securely. 6. (Model 93S / 90S International) Locate the POLAR RECEIVER ASSEMBLY (#16). Plug the POLAR RECEIVER ASSEMBLY into the POLAR RECEIVER JACK (J). Place the POLAR RECEIVER in a vertical position, POLAR RECEIVER JACK facing downward, at the front of the HANDLEBAR BRACKET TUBE (F). Position the POLAR COVER (#19) over the center of the HANDLEBAR ASSEMBLY (#15) at the HANDLEBAR BRACKET TUBE. Making sure the POLAR COVER is oriented properly, slide the POLAR COVER over the HANDLEBAR ASSEMBLY covering the POLAR RECEIVER ASSEMBLY and the end of the HANDLEBAR BRACKET TUBE. The POLAR COVER should fully nest over the HANDLEBAR ASSEMBLY. Secure the POLAR COVER using two MOUNTING SCREWS (#8). (Model 90S) Position the POLAR COVER (#19) over the center of the HANDLEBAR ASSEMBLY (#15) at the HANDLEBAR BRACKET TUBE. Making sure the POLAR COVER is oriented properly, slide the POLAR COVER over the HANDLEBAR ASSEMBLY covering the end of the HANDLEBAR BRACKET TUBE. The POLAR COVER should fully nest over the HANDLEBAR ASSEMBLY. Secure the POLAR COVER using two MOUNTING SCREWS (#8). CAUTION: DO NOT OVER-TIGHTEN THE SCREWS (#8). MISE EN GARDE : NE SERREZ PAS EXCESSIVEMENT LES VIS (N. 8). 10 3P 15 F D 17 15 4 12 K 3 5 10 D 5 11 9 L 18 K 7. Locate one of the VERTICAL HANDRAILS (#12). Carefully insert the top of the VERTICAL HANDRAIL into the user right end of the HANDLEBAR ASSEMBLY (#15). Align the mounting holes. Secure the VERTICAL HANDRAIL to the HANDLEBAR ASSEMBLY using two MOUNTING SCREWS (#4). Position the bottom of the VERTICAL HANDRAIL over the mounting hole in the top of the right FRAME LEG (K). Using one HEX HEAD BOLT (#3), mount the VERTICAL HANDRAIL to the right FRAME LEG as shown. Tighten the BOLT securely. Repeat the procedure for the remaining VERTICAL HANDRAIL (#12) on the left side of the HANDLEBAR ASSEMBLY and FRAME. 8. Lift the MONOCOLUMN SHROUD (#20) and tighten the MONOCOLUMN BOLTS (#1) securely. CAUTION: DO NOT OVER-TIGHTEN THE BOLTS (#1). MISE EN GARDE : NE SERREZ PAS TROP LES BOULONS (N. 1) 9. (Model 93S) Using four MOUNTING SCREWS (#5), attach the ACCESSORY TRAY (#11) to the DISPLAY CONSOLE (#9) as shown. CAUTION: DO NOT OVER-TIGHTEN THE SCREWS (#5). MISE EN GARDE : NE SERREZ PAS TROP LES VIS (N. 5) 10. Attach all CABLES (L) leading from the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE to the back of the DISPLAY CONSOLE (#9). 11. Feed any excess cable into the MONOCOLUMN (#10). Using four MOUNTING SCREWS (#5), secure the DISPLAY CONSOLE (#9) to the DISPLAY CONSOLE MOUNTING BRACKET (D). CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS HEAD PAN SCREWS (#5). CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HARNESS (E) WHEN ASSEMBLING THE CONSOLE ASSEMBLY (#9) TO THE DISPLAY CONSOLE MOUNTING BRACKET (D). MISE EN GARDE : NE SERREZ PAS TROP LES VIS CRUCIFORMES A TETE CYLINDRIQUE (N. 5). MISE EN GARDE : VEILLEZ A NE PAS PINCER LE FAISCEAU DE CABLES (E) LORS DU MONTAGE DE LA CONSOLE (N. 9) SUR SON SUPPORT (D). 12. Secure the MONOCOLUMN SHROUD (#20) to the MAIN SHROUD using four MOUNTING SCREWS (#7). CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS HEAD PAN SCREWS (#7). MISE EN GARDE : NE SERREZ PAS TROP LES VIS CRUCIFORMES A TETE CYLINDRIQUE (N. 7). 13. Insert the FRAME CAPS (#18) into the ends of the FRAME LEGS (K). PRE-OPERATION CHECKLIST • Ensure that all fasteners are tight. • Make sure the Stairclimber is properly leveled and stable. (Refer to the Operation Manual) • Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual) • Read the entire Operation manual before using the Stairclimber. LISTE DES VERIFICATIONS A EFFECTUER AVANT LA MISE EN MARCHE • Verifiez si tous les dispositifs de fixation sont serres • Verifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable. (Referez-vous au manuel d'utilisation.) • Verifiez si les contre-ecrous des verins de mise a niveau sont serres. (Referez-vous au manuel d'utilisation.) • Lisez le manuel...
Otros modelos de este manual:Formadores - 93S (642.96 kb)