Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE. Toll-Free Customer Service Number for U.S: 1-800-558-5234 Internet Address: © COPYRIGHT 2002 by HUFFY SPORTS 1 12/02 P/N 211670 McCall's REBOUNDER PARTS LIST (See Hardware Identifier) REBOUND ARM Item Qty. Part No. Description 1 1 200416 Base (Black) 2 4 200417 Casters 3 1 200419 Left Support Brace 4 1 201875 Right Support Brace 5 1 200423 Outer Pole Assembly 6 1 201876 Inner Pole, Fixed Upright 7 1 201877 T-Screw OUTER POLE GRADUATED SCALE HOPPER SUPPORT BRACE WINCH INNER POLE COLLAR TIP-IN INDICATOR WINCH HANDLE SAND BAGS 8 1 200418 Collar 9 1 200421 Winch Handle 10 1 200409 Cable Assembly 11 1 200410 Winch 12 1 201878 Graduated Scale 13 1 201879 Indicator Bracket 14 1 201888 Rebound/Tip-in Indicator 15 1 200399 Hopper 16 1 200400 Rebound Arm 17 1 200401 Ball Check Mechanism 18 2 226023 Air-Checks 19 1 201880 Allen Wrench 20 8 206246 Bolt, Hex 1/2-13 X 1.5" 21 1 204453 Bolt, Hex 3/8-16 X 1" 22 18 201890 Screw, 3/4" Long 23 2 201881 Screw, Self-Tapping, 1/4" Long 24 1 201891 Nut, 5/8" 25 2 202459 Nut, 1/2-13, 26 3 203017 Nut, 3/8-16 27 16 203002 Nut, 1/4-20 28 1 201884 Lockwasher 1" O.D. 29 8 201886 Lockwasher, 7/8" O.D. 30 4 201885 Lockwasher, 3/4" O.D. 31 18 201887 Lockwasher, 1/2" O.D. 32 4 201882 Pin, Clevis 33 4 201883 Screw, Clevis 34 1 200402 1/2" Steel Shaft 35 2 300382 Sand Storage Bags BASE * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. 2 P/N 211670 12/02 12/02 P/N 211670 HARDWARE IDENTIFIER Item #20 (8) Item #22 (18) Item #32 (4) Item #24 (1) Item #28 (1) Item #7 (1) Item #23 (2) Item #25 (2) Item #26 (3) Item #29 (8) Item #30 (4) Item #21 (1) Item #19 (1) Item #33 (4) Item #27 (16) Item #31 (18) 3 12/02 P/N 211670 SECTION A : ASSEMBLING THE McCALL'S REBOUNDER Tip base on it's side and install casters (2) to the bottom of base (1) as shown using bolts (22), lockwashers (31) and nuts (27). 1. 22 2 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING 31 27 2. Attach collar (8) to outer pole (5) as shown with T-Screw bolt (7). Tighten completely. 7 8 5 NOTE: THE T-SCREW (7) IS USED TO SECURE COLLAR TO OUTER POLE (5) UNTIL STRUTS ARE ATTACHED (STEP 4). AT THAT POINT THE T-SCREW (7) CAN BE LOOSENED. 6 4 P/N 211670 12/02 12/02 P/N 211670 3. 3. Attach pole assembly (5 & 6) to base (1) using bolts (20) and lockwashers (29) as shown. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Attach left (3) and right (4) support braces to base (1) and then adjust collar (8) to accommodate strut height. Attach braces (3 & 4) using bolts (20) and lockwashers (29) as shown . 20 29 4. 20 29 3 12/02 P/N 2116705 20 25 2025 29 29 4 4 3 5. 1 1 Attach graduated scale (12) to base (1) using bolt (21) and lockwasher (30) as shown. 432171110 432171 1111 1010 21 30 12 6. Attach graduated scale (12) to bracket affixed to the collar (8) as shown with nuts (25) and lockwashers (30). 2 1 1212 1 111 1 1010 9 25 12 8 30 6 P/N 211670 12/02 7. 7. Attach winch assembly (9, 10 & 11) to collar bracket using nut (25) and lockwasher (30) as shown [Winch components (9, 10 & 11) are preassembled]. 21121211111010925 9 IMPORTANT: CORD MUST PASS BEHIND SPACER AS SHOWN! Release the lever and unwind cable and attach top nut (25) and lockwasher (30) to fully secure winch assembly to collar bracket as shown. IMPORTANT: DO NOT ATTACH TOP NUT. ATTACH BOTTOM NUT ONLY. 30 10 11 TOP BOTTOM 8. 21121211111010925 Released KEEP AWAY FROM WINCH HANDLE WHEN UNWINDING -THE HANDLE WILL SPIN WHEN CORD IS UNWOUND! WARNING 30 Locked 7 12/02 P/N 211670 9. 9. Hook Indicator Bracket (13) around the Graduated Scale (12). Do not attach Rebound/Tip-in Indicator (14) yet, or the bracket will not fit around scale. 12 13 12 13 10. Attach Rebound/Tip-in Indicator (14) to indicator bracket (13) while holding bracket (13) in the position shown. The bracket/tip-in assembly (13 & 14) will not be secured until the next step (#11). 13 22 14 13 14 12 8 P/N 211670 12/02 11. 11. Attach unwound cord to indicator bracket (13) and bracket on outer pole (5) using nut (24) and lockwasher (28) as shown. 13 14 24 28 5 6 NOTE: THIS STEP FUNCTIONS TO RAISE THE OUTER POLE TO ACCOMMODATE THE DIFFERENT HEIGHTS DENOTED ON THE TIP-IN INDICATOR. 10 9 12/02 P/N 211670 12. Turn hopper (15) upside down and attach air checks (18) as shown by removing and then re-inserting the retaining (33) and clevis (32) pins connected to the air checks (18). NOTE: ITEMS (34 & 23) COME PREASSEMBLED TO THE HOPPER (15) BUT CAN BE REPLACED AND ORDERED SEPARATELY. 33 18 33 32 23 23 34 16 32 10 P/N 211670 12/02 13. 13. IMPORTANT! DO NOT EMPTY SAND FROM SAND BAGS INTO THE STORAGE BAGS. PLACE SEALED SAND BAGS COMPLETELY INTO STORAGE BAGS. 35 14 15 Tighten completely 9/16" wrench needed 5 THE HOPPER IS HEAVY! TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. DO NOT...