Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
x .5 O.D. x 1.8 Long 37 1 240017 Bolt, Hex Head, 1/4-20 x 2-1/4 Long 38 6 206311 Spacer, Plastic, .530 I.D. x .50 Long 39 7 206340 Locknut, Hex Head, 1/2-13 2 904820 Elevator Tube, Lower-Long 41 1 204838 Spring 42 1 Rim 43 2 904808 Elevator Tube, Upper-Short 44 4 201651 Spacer, 1/4 Long x 1/2 O.D. 45 2 900867 Plate, Triangle, (Black) 46 1 202814 Cap, Pole Top 47 6 206244 Bolt, Hex, 1/2-13 x 8 Long 48 1 204870 Bolt, Hex, 1/2-13 x 3-1/2 Long 49 2 203617 Plug Cap 12 201219 Smart Clip, Net Holder, 51 1 Net 52 1 201568 Anchor, T-Strap 53 1 203124 Stake, Tie Down 54 1 201252 Label, Height Adjustment and Moving 55 6 202862 Spacer .563 I.D. x 1.19 Long 56 1 203365 Rim Spacer, Plastic * You may have extra parts with this model. 7 12/03 P/N 211953C HARDWARE IDENTIFIER (BOLTS) * You may have extra parts with this model. Item #8 (1) Item #14 (1) Item #15 (2) Item #18 (2) Item #21 (3) Item #25 (3) Item #30 (2) Item #48 (1) Item #37 (1) Item #31 (1) Item #47 (6) 8 P/N 211953C 12/03 HARDWARE IDENTIFIER (NUTS & WASHERS) Item #39 (7) Item #10 (1) Item #12 (1) Item #16 (11) HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #36 (2) Item #23 (2) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #38 (6) Item #55 (6) Item #20 (3) Item #35 (1) Item #13 (7) Item #9 (1) Item #19 (4) Item #44 (4) Item #56 (4) (Not Actual Size) Item #2 (2) Item #7 (1) Item #22 (2) Item #50 (12) * You may have extra parts with this model. 9 12/03 P/N 211953C P/N 211953C 12/03 10 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: (2) 1/2” AND (2) 9/16" Wrenches 1/2” 9/16” AND/OR (2) Socket Wrenches and Sockets Item #8 Item #14 Item #15 Item #18 Item #21 Item #25 Item #30 Item #31 Item #23 Item #13 Item #16 Item #19 Item #20 Item #10 Item #12 Item #2 Item #7 Item #9 (1) Item #22 Remove all contents from underside of 11.. tank. Keep tank (1) bottom side up 1 Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 3 2 2. 1 4 5 Mark pole sections with tape as shown. TAPE (not included) 3. 6 11 12/03 P/N 211953C 5 4 IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4. 5 4 IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4. IMPORTANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 3. While maintaining alignment, bounce top & middle pole assembly (4 & 5) onto lower pole section (6) as shown until top & middle pole assembly no longer moves toward taped reference mark on bottom pole. 4 5 6 WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. 12 P/N 211953C 12/03 Install rod (7) through holes in bottom pole section (6) and eyebolt (8).6. 6. 7 4 Insert pole assembly into tank assembly as shown. 7. 8 6 6 5 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. IMPORTANT!: DO NOT OVER TIGHTEN 7 8 8. Carefully place unit on its side. Secure pole bottom (6) to tank with anchor strap (52), washers (9 & 13) and nut (10) as shown. Upright unit. Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. NOTE: 1 6 9 13 10 52 IMPORTANT!: DO NOT OVER TIGHTEN 13 12/03 P/N 211953C P/N 211953C 12/03 14 1 11 15 16 11 1 13 13 11 12 13 6 14 13 HUFFYHUFFYSPORTSSPORTS 4 16 18 18 16 17 Secure strut tubes (11) to bottom pole section (6) as shown. Once again, carefully place unit in the side position and secure strut (11) to tank (1) as shown. Completely tighten. Repeat for opposite side. Upright unit. Install pole mount bracket (17) with carriage bolts (18) as shown. Tighten flange nuts (16) completely. TIGHTEN BOLT (14) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. NOTE: FRONT SIDE 9. 10. 11. Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), and nuts (20) as shown. 12. 19 21 21 19 1920 20 19 17 22 22 23 23 Tighten just until washers ...