Iniciar sesión:
Votos - 2, Puntuación media: 3.5 ( )

Manual de usuario Precor, modelo M9.45

Fabricar: Precor
Tamaño del archivo: 134.02 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Each kit comes complete with all the hardware required to install a handrail on one side of the treadmill. If you wish handrails on both sides of the treadmill, you must order two (2) option kits. When you receive the Handrail Option kit, check its contents with the list below: Note: If you purchase both handrails, check the contents of both kits with the list below: Handrail Option Kit Contents One handrail One upper end clamp One upper center clamp Three large bolts (two 5/16 - 18 x 2.5 and one 1/4 - 20 x 2.5) One star washer One nut plate One lower clamp One 5/32" hex key One 3/16" hex key Note: To assemble the handrail(s), you will need a Phillips head screwdriver. ASSEMBLY INSTRUCTIONS The assembly of each handrail is the same on opposite sides of the treadmill. To properly install the handrail(s) on your unit, take the following steps: CAUTION: Turn OFF the unit and unplug it from the power source before installing the handrail(s). C O M M E R C I A L P R O D U C T S D I V I S I O N 1. To properly mount the lower handrail clamp, you need to install a nut plate into the guide rail. Remove the end cap from the rear of the treadmill using a Phillips head screwdriver. See Diagram 1. Important: If you are installing both handrail options, avoid misalignment of the finger guard by sliding the nut plate into position on one side of the treadmill and replace the end cap before removing the other end cap. 2. With the nut plate installed and the end cap replaced, move to the front of the treadmill. Installing the nut plate into the guide rail. Diagram 1 End cap 3. Locate the end covers on the upper handrails. See Diagram 2. Using the 3/16" hex key remove the two rear handrail end covers (the “covers” are large black washers). Discard the covers and the bolts. Replacement bolts and clamps are in this option package. Important: If you are installing both handrail options, install a handrail on one side before proceeding to the other side of the treadmill. Attach the front portion of the handrail first. This helps you determine where to position the lower handrail clamp. Electronic console Bolt End clamp Center clamp Handrail end cover Upper frame Finger guard Rear roller Bolt Attaching the front section of the handrail. Diagram 2 Upright support Handrail Guide rail Side rail Nut plate C O M M E R C I A L P R O D U C T S D I V I S I O N 4. Place the center clamp on the front portion of the handrail, followed by an end clamp. See Diagram 2. Align the two clamps with the handrail mounts on the upper frame. 5. Insert a bolt through each clamp. See Diagram 2. Using the supplied 3/16" hex key, screw each bolt through the handrail until the clamp is snug against the upright support. Do not fully tighten the bolts until you have installed the lower end of the handrail. 6. To mount the lower portion of the handrail, locate the lower handrail clamp, star washer, and lower handrail clamp bolt. Refer to Diagr...

Otros modelos de este manual:
Formadores - C940 (134.02 kb)
Formadores - C942 (134.02 kb)
Formadores - M9.41s (134.02 kb)
Formadores - c944 (134.02 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría