Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Secure harness by securing it with ty-wrap onto the side of seat frame. Console Mast Assembly 1. Install console mast cover onto console mast, making sure it is facing the right direction. 2. Straighten the loops of both wire harnesses and insert them into the bottom opening of the console mast tube. See wiring harness installation tip. Push the harness up the tube until the connectors of the harnesses appear in the opening at the top of the mast tube. WIRING HARNESS INSTALLATION TIP: Straighten the loops of the wire harness so that it can slide smoothly into the console mast. Move the console mast cover all the way to the top. Then hold the bottom of the console mast next to the console mast receptor and point the top of the console mast downward. 3. Install the console mast by sliding it into the console mast receptor while pulling the wire harness. Insert and tighten four M8x55mm Bolts using an Allen wrench. 4 Place console mast cover in place and align it with screw holes. Insert and tighten four M5x12mm screws and washers using a Phillips screwdriver. Console Assembly 1. Connect both plugs, from main wire harness and hand pulse harness, to the plug receptors on the backside of the console, taking care to install correctly (see plug alignment marks). WIRING HARNESS INSTALLATION TIP: Any excess wiring must be carefully inserted (“stored”) back into the console mast before installing the console onto the console mounting plate. 2. Fasten the console to the console mounting plate with the four M5x12mm screws and washers using a Philips screwdriver. Handlebar Assembly 1. Place the handlebar onto the mount and insert and tighten two M8x20mm screws using an Allen wrench. Note: The handlebar can be installed upside down. When installed properly, the hand grips align with the bottom of the console. Pedals 1. Using a 15mm open-end wrench to firmly affix the pedals to the cranks. The pedals should be tightened as much as possible to prevent the pedals from becoming loose. The pedals should also be checked after 8 hours of use to ensure they are affixed properly as they can loosen after use. 2. The left and right pedals are different and are denoted as right or left on the bottom of each pedal. NOTE: Left pedal threads counter-clockwise. Water Bottle 1. Place the bottle holder on the console mast. Insert and tighten the two M5x12mm screws using a Phillips screwdriver. 2. Snap the water bottle into the holder. Leveling Pad 1. Adjust all three leveling pads, located on the bottom of the stabilizer bar and the main frame, to ensure your equipment is leveled with floor. 7 1 1 5 0 S E R I E S O W N E R’ S M A N U A L 1150ES Assembly Drawing 1150ES Assembly Drawing 8 1 1 5 0 S E R I E S O W N E R’ S M A N U A L 1150ES Assembly Instructions Frame Assembly Handrail Assembly 1. Place rear stabilizer bar into the receptor and align the screw holes. 1. Place the handrail supports into their receptors on the stabilizer 2. Insert and tighten the two M8 x20mm screws, from stabilizer bar bar. Insert and finger tighten eight M8x12mm bolts, from handrail hardware bag, with an Allen wrench. assembly hardware bag, 4 on each side, to secure these supports. 2. Assemble upper handrails into handrail supports. Insert and fin- Console Mast Assembly ger tighten eight M8x12mm bolts, from handrail assembly hard1. Slide console mast cover onto console mast, making sure it is ware bag, 4 on each side, to secure these handrails. facing the right direction. 3. Place handrail clamp cover onto handrails. Assemble the hand2. Insert the main wire harness into the bottom opening of the con-rail clamp cover and handrails onto the upper portion of the console mast tube. Push the harness up to the tube until the connec-sole mast. Insert and finger tighten two M8x55mm bolts. tor of the harness appears in the opening at the top of the tube. 4. Tighten all 18 bolts of handrail assembly with an Allen wrench. WIRING HARNESS INSTALLATION HINT: Straighten the loops of the wire harness so that it can slide smoothly into the Waterbottle console mast. Move the console mast cover all the way to 1. Place the bottle holder on the console mast. Insert and tighten the top. Then hold the bottom of the console mast next to the two M5x12mm screws using a Phillips screwdriver. the console mast receptor and point the top of the console 2. Snap the water bottle into the holder. mast downward. 3. Install the console mast by sliding it onto the console mast re-Leveling Pad ceptor while pulling the wire harness. This will keep the slack 1. Adjust both leveling pads, located on the bottom of stabilizer out of the harness so the wires will not be pinched and short out. bar, to ensure your equipment is leveled with floor. Insert and tighten the four M8x12mm, from console mast hardware bag, with an Allen wrench. 4. Place console mast cover in place and align it with screw holes. Insert and tighten four M5x16mm screws using a Phillips screwdriver. Handlebar Assembly 1. Insert the ...
Otros modelos de este manual:Formadores - 1150EL (1.64 mb)
Formadores - 1150ESI (1.64 mb)
Formadores - 1150UI (1.64 mb)