Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Rectangular Tab Rim Upper Post • Lean the rim against a wall for support. • Locate the pegs on each side of the rim and the grooves on the backboard. • Position the backboard with the Fisher-Price® logo facing up. • Place your foot on the base to hold it steady and slide the backboard onto the upper post at an angle, as far as it will go. Note: There should be no gap between the upper post and the backboard. • Move the assembly away from the wall. 6 4 5 Backboard Fisher-Price® Logo Peg Groove Wall Rim Upper Post • Position the base as shown. • Position the upper post so that the straight end is down and the curved end is up and facing away from the base. Hint: For easier assembly, apply liquid soap or rub a candle or bar soap around the bottom of the upper post (especially on the corners) and the inside of the large square opening. If assembling inside, place a tarp under the base to protect the floor surface. • Insert the upper post into the large square opening in the base and, using a circular motion, push it all the way down. Assembly 5 Fisher-Price® • Move to the side of the assembly. • Place your foot on the base to hold it steady. • Press down firmly on the lower backboard while rotating the backboard up. • When properly assembled, the pegs on the upper post rest in the grooves in the backboard, as shown. 9 Top View PULL HERE PRESS HERE Peg Peg Grooves Back View Note: The height of the rim is three feet as assembled. 6 4 5 Lower Post Rib Groove Base 10 • Align the rib on the bottom of the lower post with the groove in the opening in the base. • Insert the lower post into the opening and push down, using a circular motion, until it snaps into place. IMPORTANT! Assembly of the lower post is a permanent assembly. Hint: For easier assembly, apply a small amount of liquid soap around the bottom of the post. If assembling inside, place a tarp under the base to protect the floor surface. • Align the lever on the side of the collar with the opening in the top of the lower post. • Fit the collar onto the lower post, making sure the peg on each side of the collar snaps into the hole on each side of the post. Collar Lever Opening Lower Post Hole Peg 11 Note: The collar may already be factory assembled. • If the lever comes off, simply re-attach it. • Insert the peg on one side of the lever into the hole in the collar. • Snap the other peg in the lever into the other hole in the collar. Assembly is now complete. Please refer to assembly step 2 to fill the base with water or approximately 50 lbs. of sand (water and sand not included) to keep this product stationary. Holes Peg Peg 12 4 5 6 • As assembled, the rim height is three feet. •To raise the rim height to four, five or six feet, place your foot on the base and pull up on the backboard with both hands to remove the upper post from the base. You may need to rock the upper post to loosen it from the base. IMPORTANT! Rim height should only be adjusted by an adult. Also, make sure children are not standing below the rim when adjusting the rim height. 5 4 6 Slots Lever Backboard Base Upper Post Upper Post Lower Post Adjusting the Rim Height 1 3 Care •To clean, use a mild soap and water solution and clean cloth. Rinse clean with warm water to remove soap residue. • Be sure to drain water from the base before extended storage. If water freezes in the base, it could cause damage. • This toy includes an inflatable ball. If the ball becomes soft, inflate it with a standard, hand-operated air pump with a standard air needle. • The ball will contain the correct amount of air when its circumference measures 21 to 22 inches. Measure the circumference of the ball with a tape measure or with a piece of string cut 21 to 22 inches long. Do not overinflate the ball. •To lower the rim height: while holding the upper post, push the lever on the lower post down. Lower the upper post and push the lever into the slot at 4' or 5'. •To raise the rim height: simply lift the upper post and push the lever into the slot at 5' or 6'. IMPORTANT! Since this may require a lot of force, make sure you are not standing with your face or chest above the backboard. 5 4 6 Lever Base Slots Upper Post Lower Post 2 • Pull the lever on the lower post down. • Insert the upper post into the lower post with the net positioned over the wheels on the base. • Push the lever into one of the slots ...
Otros modelos de este manual:Formadores - GROW TO PRO BASKETBALL 72408 (179.11 kb)