Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
NOTE: After replacing the battery, Joule must relearn the coded ID for the sensor. Reference Joule user guide for instructions (available at 4. Using the new battery (compatible CR2032), remove the battery cover on the back of the cadence sensor by turning counterclockwise approximately one half turn. Replace the old battery with the new battery. 5. Secure the cadence sensor to the main frame using the previously removed bolt and 4mm Allen wrench. Be sure to hold the cadence sensor arm while attaching bolt. 10 Adjust Flywheel/Chain Tension Over time and after substantial use, the chain on the CycleOps Pro Series indoor cycle will stretch. Adjusting the tension/alignment is a diffi cult task and improper adjustment can lead to premature chain/cog wear. It is recommended this task be done with assistance from an authorized indoor cycle dealer. The chain tension has been adjusted properly when there is little or no play felt when the pedals are rocked back and forth. NOTE: Be sure to make small incremental adjustments to the tensioning hardware on both sides of the fl ywheel. Only adjusting one side will lead to improper fl ywheel alignment and unwanted drive train wear and/or noise. CAUTION: Improper chain adjustment will cause premature wear and may void the warranty. CAUTION: NEVER put hands into or near the drive train while it is motion! 1. Using a 4mm Allen wrench, remove the three chain guard bolts. 3. Use a 17mm cone wrench to hold the axle locking nuts in place. Do not turn the wrench, it is only used as a stabilizer. With the other hand, use a 15mm box wrench to loosen the fl ange nuts on the axle. Repeat this process on each side of the fl ywheel. 4. Using a 10mm box wrench, adjust the tensioning hardware until the proper chain tension is achieved evenly on both sides. 5. Pull chain down (midway between chain ring and gear) to measure vertical travel. Vertical travel should be approximately 1/4” when the chain has been properly adjusted. Tighten fl ange nuts to 75 in-lbs. Do not overtighten. 10 mm tensioning hardware Flange Nut Axle Lock Nut Vertical Travel 2. Pull chain down (midway between chain ring and gear) to measure vertical travel. Vertical travel should be approximately 1/4”. Vertical travel with signifi - cantly more or less than 1/4” should be adjusted. Vertical Travel 11 1. Back off resistance until it the knob stops turning (counterclockwise). Then turn clockwise 180 degrees (1/2 turn). 2. Loosen the clamping bolts with a 5mm Allen wrench. Align the brake pad by sliding it towards the fl ywheel. Stop when the pad just touches the fl ywheel. Align the arc of the brake pad with the arc of the fl ywheel. 3. Tighten clamping bolts to 50 in-lbs. When properly adjusted, the CycleOps Pro Series indoor cycle should register around 30 watts at 90 rpm at the lowest resistance setting (can only be validated on 300 Pro). CHAPTER 6: PREVEnTATiVE mAinTEnAnCE Performing necessary preventative maintenance is key to keeping the CycleOps Pro Series indoor cycle in proper working condition. Following the recommended maintenance procedures will help extend the life of the CycleOps Pro Series indoor cycle. NOTE: Never use abrasive cleaning liquids or petroleum-based solvents when wiping down the indoor cycle. ANy CLEANING LIQUIDS MUST BE OF A MILD PH such as Dawn dish washing liquid, Pine Sol, Murphy’s Oil Soap and Mr. Clean. A standard bike polish can be used on the painted parts of the indoor cycle. DAILy After each day the indoor cycle is ridden, perform the following: • Release all tension from the resistance knob. • Wipe down the handlebar. • Wipe down seat/seat post. • Wipe down fl ywheel. • Wipe down frame. • Wipe down chain guard. • Wipe down resistance knob. • Wipe down handlebar post. • Wipe down stabilizers. Adjust Brake Pad (100 Pro, 200 Pro, 300 Pro only) The brake mechanism has been adjusted at the factory. However, over time due to chain stretch and brake pad wear, it may need to be adjusted. To replace/adjust brake pad, use the following procedure: Adjust Brake Pad (400 Pro only) The brake mechanism has been adjusted at the factory and has an electronically adjusted brake pad. Instead of manually adjusting the brake pad, plug the indoor cycle in for 60 seconds and then remove the plug. This resets and places the brake pad in the furthest position (lightest resistance). 12 Weekl y In addition to daily maintenance, perform the following each week: • Inspect and adjust brake pad. • Properly tighten pedals and all hardware attaching toe clips/straps (if applicable). Tighten pedals to 300 in-lbs. • Inspect handlebar clamp assembly. Tighten clamp bolt if loose. • Inspect seat post clamp and clamp assembly. Tighten clamp bolt if loose. • Inspect stabilizer feet. Tighten if necessary. • Inspect flywheel. Check for proper alignment. Tighten flange locking nuts to 75 in-lbs. Monthl y In addition to daily and weekly maintenance, perform the following each month: • Remove handlebar po...
Otros modelos de este manual:Formadores - 200 PRO (7.2 mb)
Formadores - 100 PRO (7.2 mb)
Formadores - 400 PRO (7.2 mb)