Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
7. Attach the Left and Right Frames (4, 5) to the Left and Right Bases (1, 2) with four M10 x 85mm Button Bolts (51) and four M10 Nylon Locknuts (65). 8 5 52 50 50 3 65 50 50 52 52 2 1 7 65 51 51 1 2 65 65 65 4 5 32 65 64 48 4 7 31 Grease 70 5 6 7 9 8. Attach the Top Cover (23) and the Bottom Cover (24) to the Center Frame (7) with two M4 x 15mm Screws (58) and an M4 x 30mm Screw (63). Attach the Center Frame Extension (6) to the Center Frame (7) with two M10 x 53mm Button Bolts (49) and two M10 Nylon Locknuts (65). 8 7 58 58 63 23 24 6 49 65 9. Orient the Headrest Frame (9) and the Backrest Frame (8) as shown. Attach the Headrest Frame to the Backrest Frame with two M10 x 16mm Button Screws (54). 9 9 8 54 54 10. Apply a small amount of grease to an M10 x 95mm Button Bolt (73). Pull the Long Adjustment Knob (37) out as far as it will go. Insert the bracket on the Backrest Frame (8) into the Top Cover (23). Next, attach the Backrest Frame to the Center Frame Extension (6) with the M10 x 95mm Button Bolt (73) and an M10 Nylon Locknut (65). Then, engage the Long Adjustment Knob into one of the holes in the bracket. See the inset drawing. Attach an M8 x 16mm Button Bolt (61) and an M8 Nylon Locknut (72) to the hole in the end of the bracket on the Backrest Frame (8). 10 6 23 Bracket 65 73 Grease 8 37 61 8 72 10 11. See the left inset drawing. Identify the Top Tube (16), the Bottom Tube (17), and the Ankle Brace Tube (18); the Tubes have different lengths and holes in different positions. Orient the Top Tube (16) and the Bottom Tube (17) so that the largest holes are on top (see the right inset drawing), and insert them into the indicated holes in the Leg Frame (10). Attach each Tube with an M4 x 15mm Screw (58). Orient the Ankle Brace Tube (18) as shown, and insert it into the Leg Frame (10). Attach the Ankle Brace Tube with two M4 x 15mm Screws (58). Make sure that the M4 x 15mm Screws (58) are tightened into the holes in the bottoms of the Tubes (16, 17, 18). 12. Set the Foot Plate (19) on the Top Tube (16) and the Bottom Tube (17). Finger tighten four M4 x 25mm Screws (60) through the Tubes into the Foot Plate. Do not tighten the Screws yet. 13. Slide the Lock Frame (11) onto the notched bracket on the Leg Frame (10), and insert the lower end of the Lock Frame into the slot in the Foot Plate (19). Attach the Lock Frame with an M10 x 75mm Button Bolt (57), two M10 Washers (68), two 16mm Spacers (46), and an M10 Nylon Locknut (65) as shown. Make sure that the Button Bolt is inserted through the hole in the lower end of the Lock Frame. See step 12. Tighten the four M4 x 25mm Screws (60). Pull the Ankle Lock Assembly (33) upward and pivot the Lock Frame (11) over the indicated notch in the bracket on the Leg Frame (10). Release the Lock Handle and engage the Lock Frame into the notch. See the inset drawing. Attach an M8 x 16mm Button Bolt (61) and an M8 Nylon Locknut (72) to the hole in the end of the bracket on the Leg Frame (10). 17 16 58 58 10 12 60 16 17 19 60 13 Notch 33 11 10 19 57 46 61 10 72 18 Holes 58 Slot 68 68 65 46 Holes Largest holes must be on top 17 16 17 18 16 11 11 14. Identify the two Rear Ankle Braces (34), which have holes in the indicated locations. Slide a Rear Ankle Brace (34) onto the Ankle Brace Tube (18). Attach the Rear Ankle Brace with two M4 x 15mm Screws (58). Make sure that the Screws are tightened into the indicated holes in the Ankle Brace Tube. Next, press a 19mm Round Cap (45) into the Ankle Brace Tube, and attach the Round Cap with an M4 x 15mm Screw (58). Attach the other Rear Ankle Brace (34) to the Ankle Brace Tube (18) in the same way. 15. Slide a Front Ankle Brace (22) onto the round tube on the Lock Frame (11). Next, press a 19mm Round Cap (45) into the round tube, and attach the Round Cap with an M4 x 15mm Screw (58). Attach the other Front Ankle Brace (22) in the same way. 34 18 Holes Holes 34 58 58 45 15 58 22 22 11 45 14 16. Pull the Short Adjustment Knob (74) out as far as it will go, and insert the end of the Leg Frame (10) a few inches into the Backrest Frame (8). See the inset drawing. Press the round tab on the Leg Frame Bushing (38), and press the Leg Frame Bushing upward into the Backrest Frame (8). Make sure that the round tab is in the indicated hole in the Backrest Frame. Then, slide the Leg Frame (10) farther into the Backrest Frame (8), and engage the Short Adjustment Knob (74) into one of the holes in the Leg Frame. 8 10 74 Holes 16 10 38 8 Hole Tab 12 17. Attach the Headrest (20) to the Headrest Frame (9) with two M6 x 18mm Button Screws (55), an M6 x 55mm Button Screw (56), and three M6 Washers (62). Attach the Backrest (21) to the Backrest Frame (8) in the same way. 17 20 21 8 62 62 18. Attach a Handle (12) to the Left Frame (4) with two M10 x 80mm Button Bolts (52), two M10 Curved Washers (50), and two M10 Nylon Locknuts (65). Attach the other Handle (12) in the same way. Make sure that all parts are properly tightened before you use the inversion t...