Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Partially fold the Frame (56) so that the treadmill is more stable; do not fully fold the Frame yet. Remove and discard the two indicated bolts (A) and the shipping bracket (B). Cut the shipping tie securing the Upright Wire (38) to the Base (83). Locate a tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole. Attach a Base Pad (81) to the Base (83) in the location shown with a #8 x 1" Tek Screw (2) and a Base Pad Spacer (13). Then, attach another Base Pad (81) with only a #8 x 1" Tek Screw (2). 83 2 56 B A 81 1 81 2 38 Hole 13 8 6. Set the Left Upright Spacer (76) on the Base (83). Have a second person hold the Left Upright (74) near the Base. Hold a Bolt Spacer (80) inside the lower end of the Left Upright. Insert a 3/8" x 4" Bolt (6) with a 3/8" Star Washer (9) into the Left Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (80), 3/8" x 4" Bolt (6), and 3/8" Star Washer (9). Then, set the Left Upright in the Left Upright Spacer. Partially tighten the 3/8" x 4" Bolts (6); do not fully tighten the Bolts yet. Press a Base Endcap (77) into the Base (83). With the help of a second person, tip the treadmill so that the Base (83) is flat on the floor. 76 74 6 83 77 6 5. With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (56) so that the treadmill is more stable; do not fully fold the Frame yet. Remove and discard the two indicated bolts (A) and the shipping bracket (B). Attach a Base Pad (81) to the Base (83) in the location shown with a #8 x 1" Tek Screw (2) and a Base Pad Spacer (13). Then, attach another Base Pad (81) with only a #8 x 1" Tek Screw (2). Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4), and the shipping bracket (C) from the Base (83). Attach a Wheel (84) with the Bolt and the Nut that you just removed. Do not overtighten the Nut; the Wheel must turn freely. Discard the shipping bracket. 5 83 B A 84 56 8 C 81 2 4 2 4. Hold a Bolt Spacer (80) inside the lower end of the Right Upright (78). Insert a 3/8" x 4" Bolt (6) with a 3/8" Star Washer (9) into the Right Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (80), 3/8" x 4" Bolt (6), and 3/8" Star Washer (9). Then, set the Right Upright in the Right Upright Spacer (79). Be careful not to pinch the Upright Wire (38). Partially tighten the 3/8" x 4" Bolts (6); do not fully tighten the Bolts yet. Press a Base Endcap (77) into the Base (83). 79 78 77 6 4 38 9 9 83 80 81 13 80 9 7. Attach the Tray (90) to the handrail assembly with two #8 x 1/2" Screws (1). Have a second person hold the handrail assembly near the Right Upright (78) and the Left Upright (74). Connect the Upright Wire (38) to the console wire. See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Remove the wire tie from the Upright Wire (38). 1 78 74 1 Console Wire Wire Tie 7 8. Set the handrail assembly on the Uprights (74, 78). Be careful not to pinch the wires. Attach the handrail assembly to the Uprights (74, 78) with six 5/16" x 1" Bolts (7) and six 5/16" Star Washers (10) as shown. See assembly steps 4 and 6. Firmly tighten the 3/8" x 4" Bolts (6). 7 10 74 Handrail Assembly 8 9. With the help of a second person, hold the console assembly near the handrail assembly. Connect the two wires from the console assembly to the two wires from the handrail assembly. See the inset drawing in step 7. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Handrail Assembly Console Assembly 9 38 Console Wire Handrail Assembly 38 7 78 10 7 7 10 10 Wires Wires 90 12. Raise the Frame (56) to the position shown. Have a second person hold the Frame until this step is completed. Orient the Storage Latch (53) so that the large barrel and the Latch Knob (54) are in the positions shown. Attach the Latch Bracket (14) and Storage Latch (53) to the Base (83) with two 3/8" x 2" Bolts (4) and two 3/8" Nuts (8). Attach the upper end of the Storage Latch (53) to the bracket on the Frame (56) with a 3/8" x 2" Bolt (4) and a 3/8" Nut (8). Note: It may be necessary to move the Frame back and forth to align the Storage Latch with the bracket. Lower the Frame (56) (see HOW TO LOWER THE TREADMILL FOR USE on page 24). 53 8 8 Large Barrel 83 4 56 14 12 4 11. Identify the Storage Latch (53). Remove the tie from the end of the tube. Make sure that the sleeve has been slid over the indicated hole and that the Latch Knob (54) is locked into the hole. Pull on the sleeve to make sure that it is locked into place. 54 Sleeve Tube Hole 53 10. Insert the wires from the console assembly into the handrail assembly. Attach the console assembly to t...