Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
It is the owner's responsibility to ensure that all users of this exercise bike have read the Owner's Manual and are familiar with warnings and safety precautions. • This exercise bike has a maximum user capacity of 250 pounds. • The Discovery exercise unit should only be used on a level surface and is intended for indoor use only. It should not be placed in a garage, patio or near water. Keys recommends an equipment mat be placed under the unit to the protect the floor or carpet and for easier cleaning. • Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use this exercise bike with bare feet, sandals, socks or stockings! • Always examine your exercise bike before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the exercise unit. • Never operate the exercise bicycle where oxygen is being administered or where aerosol products are being used. • Never insert any object or body parts into any opening. • Service to your Discovery unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys technician. Failure to follow these instructions will void the warranty. 2 Assembly of DISCOVERY 5.2 Hybrid REMOVE ALL SECURITY TAPE AND WRAPPING BEFORE BEGINNING. Pedal Rear Stabilizer Front Stabilizer Mainframe Seat Post Handlebar Post Resistance Knob Handlebar Computer Seat Handlebar 3 4 6X13 Washer(64)-4 8X19 Arc Washer(15)-12 10X26 Washer(37)-4 M6 Cap nut (65)-4 10X13X14 Screw Driver M8x15mm Screw (11)-8 3/8" Nylock nut(39)-4 M8 Cap nut(14)-4 M6X40mm Carriage Bolt(63)-4 17X13X14 Screw Driver M5 Allen Wrench 3/8"x45 Hex Head Screw(53)-4 M8X70mm Carriage Bolt(12)-4 11 59B 59A 59A 59B A B 60 2-1 59A 2 15 15 2 15 50 62 11 2 59B 14 15 14 11 4 12 1 14 15 12 1 3 14 15 1. Attach the front stabilizer (3) to the main frame (1) with carriage bolt, washers and cap nuts (12,15,14). Attach the rear stabilizer (4) to the main frame (1) with carriage bolt, washers and cap nuts (12,15,14) 2. Connect sensor cable (50) to the extension wire (62). Secure the handlebar post (2) with screws and washers (11,15). 2-1. Guide the cable from the resistance knob (59A) through the eyelet (see picture A). Then pull the resistance knob (59A) over the gap of the resistance cable (59B) (see picture B). 5 6 8R 37 39 8L 53 39 37 4 53 68 6R 7 68 22L 68 6L 22L 44 2 3 44 1 7 22R 68 22L 3. Attach the sleeve (6L, 6R) to the handlebar post (2) with washers, nylon lock nut and platic cap (44, 22L, 68). Attach the pedal tube arm (7) to the crank with nylon lock nut (22L, 22R). 4. Connect the pedals (8L,8R) onto the pedal tube (7) with the nylon lock nut (39), washers (37) and screws (53). Each pedal is marked “L” for left and “R” for right. 11 6 5 2 15 79 79 78 70 51 54 79 58 55 78 5. Assemble the seat (55) to the seat post tube (54) and fasten the nylon lock nuts and attachment bar (78,58). Release the seat knob (51) and then insert the seat post (70) into the mainframe. Secure the desired height by tightening the knob. 6. Attach the small handlebars (56) to the handlebar post (2) with screws and washers (11,15). 7 8 8 2 64 65 64 5 66 63 5 57 62 61 49 62 7 57 61 7. Connect the extension wire (62) that protrudes from the upright tube into the jack of the computer (61). Attach the computer to the upright tube with nuts (49). Connect pulse wires (57) to computer (61). 8. Attach two handlebars (5) onto the axles of the handlebar post (2) with the carriage bolts (63), washers (64) and cap nuts (65). DCV 5.2H PARTS LIST DCV 5.2H PARTS LIST DCV5.2H Parts List Rev C REF # ITEM DESCRIPTION QTY REF # ITEM DESCRIPTION QTY 1 323-00217 MAIN FRAME # 1 1 41 319-00092 IDLER WHEEL #41 1 2 323-00127 CONSOLE TUBE DCV5.2H/EL 1 42 319-00093 NYLOCK NUT M10 #42 1 3 323-00218 FRONT STABILIZER # 3 1 43 302-00637 IDLER WHEEL SPRING#43 1 4 323-00219 REAR STABILIZER # 4 1 44 302-00638 WASHER#44 4 5 323-00308 FRAME, REVISED FOR NEW TRANS WHEEL 2 45 302-00639 SCREW 4X8#45 1 6L 323-00310 SLEEVE DCV5.2H 1 46 319-00094 ARC MAGNET PLATE R110X2.0 # 46 1 6R 323-00220 SLEEVE (RIGHT) # 6R 1 47 302-00640 ARC MAGNETIC SPRING #47 1 7 323-00309 DCV5.2H/EL #7 2 48 302-00641 HEX HEAD SCREW M8X60 #48 2 8L 306-00434 PEDAL L, DCV5.2H 1 49 302-00642 NYLOCK NUT M8 #49 1 8R 306-00435 PEDAL R, DCV5.2H 1 50 313-00133 REED SWITCH TRI-6.0R 1 9 306-00430 FRONT WHEEL CAP #9, DCV5.2H 2 51 302-00643 SPRING KNOB#51 1 10 306-00432 END CAP, TRI-5.3E, 8.3E 2 52 302-00644 BUSHING#52 1 11 302-00620 SCREW M8X15 # 11 8 53 302-00645 HEX HEAD SCREW 3/8"X45#53 4 12 302-00621 CARRIAGE SCREW M8X70 # 12 4 54 319-00095 SEAT POST #54 1 13 302-00622 WASHER # 13 3 55 306-00436 SEAT, DCV5.2H 1 14 302-00623 NYLOCK NUT M8 # 14 4 56 319-00096 HANDLEBAR TUBE #56 1 15 302-00624 ARC WASHER # 15 12 57 313-00134 HAND PULSE TRI-6.0R 1 16 331-00069 BALLBEARING (L) #16 1 58 302-00646 NUT COVER M8#58 1 17 331-00025 BEARING RIGHT 1 59A 310-00169 UPPER TENSION KNOB WIRE, DCV5.2H 1 18 319-00088 MAGNET #18 1 59B ...