Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
9. Allow the belt to fully stop before dismounting. 10. Pets should never be allowed near or on the treadmill. 11. Close supervision is necessary when this appliance is used by or near children, invalids or disabled persons. 12. Never operate the treadmill where oxygen is being administered, or where aerosol products are being used. 13. Never insert any object or body parts into any opening. 14. For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time. 15. Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer 16. Failure to follow these instructions will void the treadmill warranty. 17. Never leave the treadmill unattended when plugged in. Unplug from outlet when not in use and before service or maintenance. 18. Always unplug this appliance immediately after using and before cleaning. To disconnect, turn all controls to the off position, then remove plug from outlet. 3 Before You Start Thank you for purchasing the HEALTH TRAINER 402t Treadmill! This quality product you have chosen was designed to meet your needs for cardiovascular exercise. Before you start, please read the Owner's Manual and become familiar with the operation of your new treadmill. Remember to take the time to perform the stretching exercises provided to avoid injury. Do not stand on the walking belt while pressing the Power button or Start/Stop button. Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds. If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate. If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set treadmill programs or start an exercise program without first contacting and receiving approval from your physician. To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys Fitness recommends a sealed water bottle for beverages consumed while using the treadmill. Please review the following drawing below to familiarize yourself with the listed parts. 4 CONSOLE SAFETY KEY RIGHT UPRIGHT LEFT UPRIGHT RUNNING BELT TRANSPORT WHEEL MOTOR COVER LATCH POWER CORD END CAPS BASE TOP RAIL Assembly The HEALTH TRAINER 402t treadmill will require assembly before operating. After opening the box, remove any packing material from the treadmill. Do not throw away any packing materials until the unit is working properly. Place the base on a clean, level surface. Make sure the electrical cord will easily reach an electrical outlet. Locate the hardware pack and identify the following parts required for assembly. Assembly Parts: 1. Owner’s Manual 2. Console Assembly 3. Left and Right Uprights 4. Top Rail 5. Allen Wrench 6. Arc Washer 10*20*1.5 mm (10) 7. Allen Bolt M8*15 mm (10) 8. Allen Bolts M5*15 mm (4) 5 CONSOLE RIGHT UPRIGHT LEFT UPRIGHT TOP RAIL BASE ALLEN WRENCH ALLEN BOLT M8X15 10PCS ARC WASHER .10X.20X1.5 10PCS Owber’s Manual Assembly Assembly requires the included allen wrench and your own phillips screwdriver. Do not plug in the power cord until all assembly step are completed. 1. With the treadmill deck in the down position, leave the unit on the original packing material to assemble all parts.Refer to Figure 1. 6 Figure 1: Deck in down position Figure 2: Left and Right Upright Installation Figure 3: Top Rail Grommet Assembly 2. Feed the cable thru the Right Upright until the connector is exposed. Install Right Upright to base using 4 Allen Bolts M8*15mm and Four Arc Washers. Hand tighten all hardware at this time. Repeat for Left Upright . Refer to Figure 2. Note: Be careful not to pinch the wire harness. 3. Use the drag line to pull Console Wire Harness thru the top rail as shown in Figure 3. Place the grommet over the Console Wire Harness and install the grommet in the top rail. Note: Be careful not to pinch the wire harness. DRAG LINE GROMMET Assembly 7 Figure 4: Top Rail Assembly 4. Attach the top rail to the left and right uprights using 2 Allen Bolts M5*15 and 2 Arc Washers. You may now firmly tighten all hardware. Refer to Figure 4. Note: Be careful not to pinch the wire harness. 5. Remove the four M5*20mm screws from the back of the console. Set aside. Connect Console Wire Harness being careful not to pinch the wires. Using four screws previously removed from console, attach console to the Top Rail. Refer to Figure 5. CONSOLE Figure 5: Console Wire Connections CONGRATULATIONS!!!!!!!! You have completed assembly of your HealthTrainer 402t Treadmill. Warm Up Exercises EXERCISE GUIDELINES WARNING! Before beginning this or any exercise program, you should consult your physician. This is especially important for individuals over the age of 35 or individuals with pre-existing health problems. Warming up prepares th...