Votos - 6, Puntuación media: 4
(
)
)
|
Resumen del manual
CONTROL PANEL FUNCTION Power On /Off: Press to control the main power of the sauna unit. Power indicator: Indicates the status of the sauna’s main power. Work Start/Stop: Press to control the working functions of the sauna. Work indicator: Indicate the working status of the sauna. Heat indicator: Indicate the status of heating functions. Light: Press to control the lighting function Time Display: Display the heating time of the sauna in minute(s) Time: Press to adjust the setting of the timer. Temperature Display: Display the actual interior temperature of the sauna room in 0C/0F. Temperature: Press to adjust the temperature setting 0C/0F: Press to change the temperature display between 0C or 0F. 1. MAIN POWER: Plug in the main power to your household power. 2. SAUNA POWER: To power on the sauna, press POWER ON/OFF one time on the inside control panel, POWER light should then light up, The TIME DISPLAY will flash 60. TEMPERATURE DISPLAY will flash 60. If you press POWER ON/OFF again, power is off, while everything goes out. 3. HEATING TIME: When power is on, press TIME “^” or “Ў” to increase or decrease the emitting time of sauna room. When you press one time, it increases or decreases 1 minute. If you press the set-up button continuously for more than 2 seconds, the digital will change quickly. If you don’t press the button in more than 5 seconds, the digital will stop flashing, set-up value will be memorized. This value will be shown when you restart next time. During sauna session, set-up time will count down the minutes one by one. When the left time is 5 minutes, the equipment will make a warning sound for 15 seconds, at this moment, time display is flashing. During these 15 seconds, you can press any set-up button to stop warning sound, and reset up the time of new sauna session. If you don’t set up the time again, after 15seconds, sauna continues, when display time is 0, the equipment will power off automatically. Particularly the equipment will also power off if you don’t press any bottom in 5 minutes after you power on the sauna! 4. Switch between 0F and 0C When power is on, “0C” and “0F” will switch when you press “0C/0F”. And the TEMPERATURE DISPLAY value will change accordingly. 5. Set up the heating temperature When you turn the power on, press TEMPERATURE button “^” or “Ў” to increase or decrease the heating temperature of sauna room. The temperature will increase or decrease I minute when you press one time. If you press the set-up button continuously for more than 2 seconds, the digital will change quickly. This value will be the set-up sauna temperature. If you don’t press the button in more than 5 seconds, the digital will stop flashing, set-up value will be memorized. It will show this value when you restart the next time. 6. Start emitting or stop emitting When powering the sauna on, press WORK START/STOP button one time, WORK and HEAT light is on, the emitters will start emitting. (If you press this button again, emitters are off, WORK and HEAT light is off.) In the summer (room temperature is around 300C/860F), (such as 2 person sauna) heating time and actual inside temperature like the following datasheet: actual inside temperature 400C(1040F) 500C(1220F) 550C(1310F) 600C(1400F) Heating time (minutes) 5~7 17~19 23~25 31~33 When environmental temperature is low, heating requires additional time. The above data is only for your reference. When the temperature is at the set-up value, the digital control will maintain the set temperature. The WORK light will remain on and the HEAT light will turn off. When the top heating, the sauna will maintain the set-up temperature for some time, when the inside temperature drops 20C, the digital control will make the emitters continue heating until it reaches the set-up value. With the digital control, the inside sauna temperature is always around the set-up value. 7. Inside reading lamp switch 1) Press the light ON/OFF button one time to switch on, press again to switch off. 8. How to use CD/Radio 1) To use the CD/Radio Press PWR to turn on the CD/Radio. Press BAND to choose FM/AM frequency of the radio. Note: when you listen to the radio, please take the antenna out of the top cover to receive a good signal, press LO/RPT to choose the receiving flexibility of far or near radio stations. Turn the tuner to select a radio station. Insert the CD disk correctly in the front of CD/Radio, press to play music. Press in to stop music. Under the mode of CD music, press to track backward. Under the mode of CD music, press to track forward. Use “SEL” switch to change sound effect, after you press SEL, press VUP or VDN to adjust the volume. Press SEL in turn to choose circularly among volume > low volume > high volume > balance > volume. Press LUD/RDM to strengthen bass effect, press for 2 seconds to choose the function of stochastic play. Under the mode of CD music, press LO/RPT, to choose the function of playback. Under the mode of CD music, press MO/INT, you...