Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Do not fully tighten the Bolts. 4 A 21 39 39 Note: The Caps mentioned in all assembly steps may come pre-assembled from the factory. 2. Press a 2” Square Inner Cap (29) into the lower end of the Left Upright (8). 2 Welded Nut Attach the Left Upright (8) to the Left Base (6) with a Support Plate (28), two M8 x 65mm Bolts (42) and two M8 Nylon Locknuts (40). Do not confuse the Left and Right Upright. Locate the welded nut to identify each Upright. 8 42 Do not tighten the Nylon Locknuts yet. 40 28 6 29 6 3. Press a 2” Square Inner Cap (29) into the lower end of the Right Upright (9). Attach the Right Upright (9) to the Right Base (7) with a Support Plate (28), two M8 x 65mm Bolts (42) and two M8 Nylon Locknuts (40). 4. Insert an M8 x 55mm Carriage Bolt (47) through the front hole in each Base (6, 7). Slide the mounting bracket (B) on the Bench Frame (5) onto the Carriage Bolts. Partially tighten an M8 Nylon Locknut (40) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Insert two M8 x 60mm Bolts (48) through the mounting bracket (B) on the Bench Frame (5) and the Left and Right Base (6, 7). Tighten an M8 Nylon Locknut (40) onto each Bolt. Tighten the Bolts (39) and Locknuts (40) used in steps 1–4 now. 5. Press an Outer Upright Bushing (46) onto the top end of each Upright (8, 9). Slide a Weight Rest (11) into the Right Upright (9). Align one of the holes in the Weight Rest with the hole in the Upright. Insert an M10 Adjustment Knob (25) through the Upright and the Weight Rest. Tighten the Knob into the welded nut. Insert the other Weight Rest into the Left Upright (8) in the same manner. Both Weight Rests must be set at the same height. 6. Press a 1 1/4” Square Inner Cap (34) into each end of the Adjustment Tube (12). Insert the Adjustment Tube into one set of adjustment brackets (C) on the Uprights (8, 9). Make sure the Adjustment Tube (12) is oriented as shown and that the pins on the Tube are fully inserted into the slots in the adjustment brackets (C). 3 7 40 42 29 28 9 4 5 40 6 40 47 B 48 7 5 8 11 46 25 11 Welded Nut 9 6 8 34 C Pin 12 34 9 7 8 7. Insert a 1” Square Inner Cap (32) into the open end of each Backrest Tube (13, 14). Insert a 10mm Plastic Bushing (35) into each end of the welded tubes on the Backrest Tubes (13, 14) as shown in the inset drawing. Identify the Left (13) and Right (14) Backrest Tube. The welded tube on the front end extends on one side. This protrusion must be pointed towards the center of the bench as shown in the inset drawing. 7 8. Refer to the inset drawing for this step. Lubricate an M10 x 175mm Bolt (43) and slide an M10 Washer (37) onto it. Push the Bolt through the welded tube on the Left Backrest Tube (13). Insert the Bolt through the indicated hole in the Left Seat Bracket (1). Make sure you have identified the Left Seat Bracket and that it is oriented as shown in the drawing. Slide a Plastic Spacer (20) onto the M10 x 175mm Bolt (43). Push the Bolt through the holes (D) in the Bench Frame. Slid...
Otros modelos de este manual:Formadores - 831.150860 (776.38 kb)
Formadores - 831.150860 (776.38 kb)
Formadores - 831.150860 (776.38 kb)
Formadores - 831.150860 (776.38 kb)