Votos - 5, Puntuación media: 3.6 ( )

Fabricar: Impex Tamaño del archivo: 857.8 kb Nombre del archivo: e69c3108-17d8-4034-94e6-a1c7d97d016e.pdf Idioma del manual:

Press two 1” Round Inner Caps (49) into the top of the crossbar (B). 7 60 61 5 19 61 21 62 25 Pin Grooves 8 25 B 76 63 64 Pin Groove Pin 9 27 55 A 44 27 27 44 49 B 7 8 13. Press Arm Assembly—Locate and open the parts bag labeled “ARM ASSEMBLY.” Press a 1” x 7/8” Plastic Bushing (75) onto each welded spacer on the Press Frame (17). Align the welded spacers on the Press Frame with the tube (A) on the Top Frame (55). Note: This will be a tight fit. The Plastic Bushings should fit onto the ends of the tube on the Top Frame. Lubricate the 3/8” x 7 1/2” Bolt (59). Attach the Press Frame to the Top Frame with the Bolt and a 3/8” Nylon Jam Nut (83). Arm Assembly 13 12. Press a 2” Square Inner Cap (27) into the Press Seat Frame (77). Slide the Press Seat Frame onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Press Base (51). Insert two 5/16” x 2 3/4” Bolts (11) through the bracket on the Seat Frame and through the holes in the Press Upright (42). Hand tighten a 5/16” Nylon Locknut (3) and a 5/16” Flat Washer (8) onto each Carriage Bolt. Tighten all Nylon Locknuts used in steps 4 through 12. 12 11. Attach the upper ends of the Weight Guides (62) to the Top Frame (55) with a 3/8” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61) and a 3/8” Nylon Locknut (21). Tighten the Nylon Locknut fully. 11 10. Place the Top Frame (55) on top of the two Uprights (56) and (42) in the direction shown. Align the holes in the Top Frame with the holes in the brackets on the Uprights. Insert four 5/16” x 2 3/4” Bolts (11) with four 5/16” Flat Washers (8) through the holes in the Top Frame (55) and the brackets on the Uprights. Hand tighten a 5/16” Nylon Locknut (3) unto each Bolt. Do not tighten the Nylon Locknuts yet. 10 11 8 8 3 3 55 61 60 21 62 1 11 8 77 42 27 3 3 59 Lubricate 83 17 75 42 56 55 55 A 51 3 14. Press a 1 3/4” Square Inner Cap (44) into the lower end of each Press Arm (46). Press a 1” Round Inner Cap (49) into the side of each Press Arm. Attach each Press Arm to the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3). 15. Butterfly Arm Assembly 14 22 46 49 44 3 17 15 Attach a “V”-Pulley (6) and a Long Cable Trap (50) to each Butterfly Arm (47) and (48) with a 3/8” x 2 1/2” Bolt (7) and a 3/8” Nylon Locknut (21). 7 Make sure the Long Cable Traps (50) are positioned as shown. Identify the Right Arm (48) and the Left Arm (47) by imagining yourself sitting on the seat. Note the position of the welded bracket (A) on each Arm. Arm identification is very important for the next step. 50 6 A A 50 6 21 48 47 9 16. Lubricate both axles (A) on the Top Frame (55). Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right and Left Arm. Make sure the upper end of the Right Arm is behind the indicated bracket (B) on the Top Frame. Tap two 1” Retainers (69) and a 1” Round Cover Cap (70) onto the right axle. Make sure the teeth on the Retainers (69) bend toward the Cover Cap (70), as shown in the inset drawing. Attach the Left Arm (47) in the same manner. Press a 1 3/4” Square Inner Cap (44) into the lower end of each Arm (47) and (48). Wet the lower end of each Arm with soapy water. Slide a 10” Pad (45) onto the lower end of each Arm. 17. Refer to the inset drawing. Attach the Bumper (82) to the Press Seat Frame (77) with the 1” Tap Screw (92). Press a 2” Square Inner Cap (27) into each end of the Leg Press Arm (89). Lubricate the 3/8” x 3 1/4” Bolt (85). Attach the Leg Press Arm (89) to the Press Base (51) with the Bolt and a 3/8” Nylon Locknut (21). Cable Assembly 18. Locate and open the parts bag labeled “Cable Assembly and Pulleys.” For Cable identification and routing during steps 18-35, refer to the Cable Diagram and Cable ID Chart on page 19. Tighten the Bolt and Locknut on the pre-assembled Pulley (15) on the Top Frame (55) Attach a “V”-Pul...

Descargar ahora

Introduzca dos números de la imagen: