Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
13 STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 87” Butterfly Cable (#42) to the clip on the Right Butterfly (#11). Draw the Cable to the right Swivel Pulley Bracket (#20). B.) Attach a Pulley (#57) to the Bracket. Secure it with one M10 x 1 .” Allen Bolt (#69), two O .” Washers (#66), and one M10 Aircraft Nut (#86). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#19). Repeat Procedure B above to install a Pulley. Let the Bracket hanging for now. D.) Draw the Cable upward to the left Swivel Pulley Bracket. Repeat Procedure B above to install another Pulley. E.) Draw the Cable around the Pulley they clip it to the Left Butterfly. DIAGRAM 7 14 STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach the 128” Lower Cable (#40) to the opening on the bottom of the Rear Vertical Beam (#6). Attach a Pulley to the opening. Insert two Pulley Bushings (#62) to the holes outside of the opening. Attach the Foot Plate (#16) to the Bushings. Align the holes and secure them with one M10 x 3 3/8” Allen Bolt (#73), two O .” Washers (#66), and one M10 Aircraft Nut (#86). B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Base (#8). Install a Pulley with a M10 x 1 .” Allen Bolt (#69), two .3/4” Washers (#66) and one M10 Aircraft Nut (#86). Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket previously installed in Step-6. Install another Pulley. C.) Draw the Cable around the Pulley then downward to the open bracket on the Rear Vertical Beam. Install another Pulley. D.) Draw the Cable around the Pulley and upward to the Single Floating Pulley Bracket previously installed in Step-7. Connect the Cable to a Short Chain (#63) by using a C-clip (#61). Attach the Short Chain to the Bracket. Secure it with a M10 x 1” Allen Bolt (#68), two O .” Washers (#66), and one M10 Aircraft Nut (#86). Adjust the tension of the Cable by adjusting the length of the Chain. E.) Secure the Foot Plate (#16) to the Weight Glide Base (#8) with two M10 x 1” Allen Bolts (#68), four O .” Washers (#66), and two M10 Aircraft Nuts (#86). F.) Connect the Long Chain (#64) to the Lower Cable with a C-clip. For various exercises, connect with one of the Shiver Bar (#30), V Bar (#88), Ankle Strap (#89), Single Handle Strap (#90), or the Triceps Rope (#91) with a C-clip. 15 DIAGRAM 8 16 STEP 9 (See Diagram 9) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#27) in between the two Safety Stop Frames (#26). Align the holes. Insert the Weight Bar (#28) into the Safety Stop Frame from one end and through the Lifting Sleeve (#27) to the other Safety Stop Frame on the opposite side. Secure the Weight Bar to each Safety Stop Frame with a M8 x 3/8” Allen Bolt (#81). B.) Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the selected holes on the Front Vertical Frames (#3). Attach a Long Olympic Sleeve (#44) to each end of the Weight Bar. Attach a Spring Clip (#60) to the Sleeve. C.) Attach six Weight Posts (#17) to the Left & Right Vertical Frames (#4&5). Secure each Weight Post with two M10 x 2 .” Carriage Bolts (#75), one 4 .” x 2” Bracket (#36), two O .” Washers (#66), and two M10 Aircraft Nuts (#86). D.) Attach six Olympic Sleeves (#43) to the Weight Posts. Attach Spring Clips (#60) to the sleeves. Insert the Left & Right Bar Holders (#21&22), the Left & Right Safety Catches (#23&24) into the selected holes on the Front Vertical Frames (#3). 17 EXPLODED DIAGRAM 18 PARTS LIST KEY NO. DESCRIPTION 1 Base Frame 2 Cross Brace 3 Front Vertical Beam 4 Left Vertical Frame Right Vertical Frame 6 Rear Vertical Beam 7 Weight Glide Post 8 Weight Glide Base 9 Upper Frame Left Butterfly 11 Right Butterfly 12 Butterfly Base 13 Butterfly Pulley Bracket 14 Sliding Weight Post Front Top Beam 16 Foot Plate 17 Weight Post 18 Double Floating Pulley Bracket 19 Single Floating Pulley Bracket Swivel Pulley Bracket 21 Left Bar Holder 22 Right Bar Holder 23 Left Safety Catch 24 Right Safety Catch Guide Rod 26 Safety Stop Frame 27 Lifting Sleeve 28 Weight Bar 29 Lat Bar Shiver Bar 31 Curl Handle 32 Chrome Panel 33 Triangle Bracket 34 5 1/8” x 2 .” Bracket 5 1/8” x 2 3/8” Bracket 36 4 .” x 2” Bracket 37 6 .” x 2” Bracket 38 Backrest Board 39 Butterfly Arm Pad 128” Lower Cable 41 132” Upper Cable 42 87” Butterfly Cable 43 Olympic Sleeve 44 Long Olympic Sleeve Curl Bar Handle Grip 46 Lat Bar Grip 47 O 1” x 3 1/8” Bushing 48 O 1 .” x 1” Bushing 49 1 .” Square End Cap 1 .” Square End Cap Q’ty 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 6 2 1 2 1 1 1 1 2 2 1 1 1 1 1 2 2 2 1 8 2 1 2 1 1 1 6 4 2 2 2 2 2 7 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 2 3/8” Square End Cap 2 2 .” x 2” End Cap 1 O 1” Cone-shaped End Cap 14 2 3/8” x 2” Sleeve 2 Sliding Sleeve 4 Lock Ring 2 Pulley 11 O 1 .” Rubber Bumper 1 O 2 .” Rub...