Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 HARDWARE IDENTIFIER 3 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Front Stabilizer (#22) to the Main Frame (#4). Secure it with two M10 x 3 1/8” Carriage Bolts (#54), one 4 .” x 1 5/8” Bracket (#26), two . .” Washers (#64), and two M10 Aircraft Nuts (#63). B.) Connect the two Rear Stabilizers (#5) with the Lat Bar Base (#6). Attach the Main Frame (#4) to the Lat Bar Base. Secure them together with two M10 x 3 3/8” Carriage Bolts (#52), . .” Washers (#64), and M10 Aircraft Nuts (#63). Diagram 1 4 STEP 2 (See Diagram 2) A.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#1). Insert the Lat Bar Frame into the opening on the Lat Bar Base (#6). B.) Attach the Cross Brace (#7) to the Lat Bar Base. Align the holes on the Lat Bar Frame, Lat Bar Base, and Cross Brace. Secure them with three M10 x 2 .” Carriage Bolts (#56), one 1 5/8” x 2” Bracket (#38), one 6 .” x 2” Bracket (#39), three . .” Washers (#64), and three M10 Aircraft Nuts (#63). Do not tighten the nuts and bolts yet. C.) Place the Backrest Adjustment Bar (#10) onto the holders on the Cross Brace. D.) Attach two Spring Clips (#34) onto the weight posts on the Sliding Weight Post (#11). E.) Insert one M10 x 2 3/8” Allen Bolt (#67) through the hole on the Lat Bar Frame. Secure it with two O .” Washers (#64) and one M10 Aircraft Nut (#63). DIAGRAM 2 5 STEP 3 (See Diagram 3) A.) Attach the bottom of Right Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right Upright Beam to the Cross Brace (#7). B.) Secure the Right Upright Beam to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts (#54), . .” Washers (#64), and M10 Aircraft Nuts (#63). C.) Secure the Right Upright Beam to the Cross Brace with two M10 x 2 .” Carriage Bolts (#56), one 4 .” x 2” Bracket (#27), two . .” Washers (#64), and two M10 Aircraft Nuts (#63). D.) Repeat Steps A, B, and C above to install the Left Upright Beam (#2). E.) Insert the Left & Right Bar Holders (#23 & 24) into the selected holes on the Upright Beam. DIAGRAM 3 6 STEP 4 (See Diagram 4) A.) Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball stopper of the Cable is underneath the Frame. B.) Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 .” Allen Bolt (#57), two O 5/8” Pulley Bushings (#43), two . .” Washers (#64), and one M10 Aircraft Nut (#63). C.) Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#55), one L-shaped Pulley Bracket (#28), two . .” Washers (#64), and one M10 Aircraft Nut (#63). D.) Pull the Cable down to the Sliding Weight Post (#11). Secure the Cable to the Post with one M10 x 1 3/8” Allen Bolt (#53), two . .” Washers (#64), and one M10 Aircraft Nut (#63). E.) Connect a Chain (#37) to the Lat Bar (#12) with a C-clip (#36). Connect the Chain to the Cable with another C-clip. 7 STEP 5 (See Diagram 5) A.) Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2 .” Allen Bolt (#57), two . .” Washers (#64), and one M10 Aircraft Nut (#63). B.) Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15). Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1 3/8” Hex Bolts (#58) and . .” Washers (#66). C.) Place the Seat (#18) onto the Seat Support (#15). Secure it with four M6 x 5/8” Hex Bolts (#60) and . .” Washers (#66). Insert a L-shaped Pin (#40) into the hole on the Seat Support to lock the Seat and Backrest Board in position. Remove the Pin when folding the Backrest Board forward to allow access to the “Walk-in Squat”. D.) Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Hex Bolts (#61) and . 5/8” Washers (#65). E.) Insert the Arm Curl Stand into the opening on the Main Frame. Secure it with a M10 Lock Knob (#33). DIAGRAM 5 8 STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#8) to the Main Frame. Secure it with M10 x 3” Allen Bolt (#59), two . .” Washers (#64), and one M10 Aircraft Nut (#63). B.) Insert one Foam Tube (#25) halfway through the hole on the Main Base Frame. Insert two Foam Tubes halfway through the holes on the Leg Developer. C.) Push six Foam Rolls (#31) onto the Foam Tubes from both ends. D.) Attach the Curl Bar Handle Frame (#13) to the Leg Developer. Secure it with a L- shaped Pin (#40). Remove the Pin and the Curl Bar when doing Leg Developer exercises. E.) Attach a Spring Clip (#34) to the weight post on the Leg Developer. DIAGRAM 6 9 10 PARTS LIST KEY NO. DESCRIPTION Q’ty 1 2 3 4 6 7 8 9...