Votos - , Puntuación media:
(
)
)
Fabricar: Impex
Tamaño del archivo: 4.34 mb
Nombre del archivo: 2d735da2-c902-4513-9b50-31417492b0a5.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
STEP 1 (See Diagram 1) A.) Attach a Floor Stabilizer (#6) and a Lower Pivot Bracket (#35) to the Base Frame (#3). Secure it with two M12 x 4” Carriage Bolts (#28), . 1” Washers (#29), and M12 Aircraft Nuts (#30). B.) Insert the Lower Pulley Bracket (#14) into the hole on the Lower Pivot Bracket (#35). Secure it with one M10 x 1” Allen Bolt (#38) and . 1 .” Washer (#39). C.) Repeat the procedure A and B above to install the other side. DIAGRAM 1 4 STEP 2 (See Diagram 2) A.) Attach a Support Frame (#2) to the Floor Stabilizer (#6). Secure it with one Bracket (#16), two M12 x 4” Carriage Bolts (#28), . 1” Washers (#29), and M12 Aircraft Nuts (#30). B.) Insert two Guide Rods (#12) into the holes on top of the Base Frame (#3). Secure each Guide Rod with one M10 x 1” Allen Bolt (#38) and . .” Washer (#32) from the bottom. C.) Slide one 1” Thick Rubber Bumper (#22) onto each Guide Rod from top. Note: WD40 or similar lubricant might be needed. Slide one Guide Rod Sleeve (#5) onto each Guide Rod from top. Then slide one more 1” Rubber Bumper (#22) onto each Guide Rod from the top. D.) Screw a Small Pulley Bracket (#8) to the top of the Weight Holder (#4). Slide the Weight Holder (#4) onto the two Guide Rods (#12) from the top. Slide one .” Thick Rubber Bumper (#23) and Olympic Sleeve (#13) onto the Weight Holder from each end. Clip one Spring Clip (#25) onto each end of Olympic Sleeve. E.) Repeat the Step A, B, C, D above to install the other side. F.) It is strongly recommended to spray lubricant such as WD-40 on the Guide Rods to minimize friction. 5 STEP 3 (See Diagram 3 & Cable Loop Diagram) A.) Attach the horizontal beam on the Crossover Frame (#1) to the top of the two Guide Rods (#12). Note: Help of a second or third person is a must!! Secure the Guide Rods with two M10 x 1” Allen Bolts (#38) and . .” Washers (#32). Repeat the same procedure to install the other side. B.) Secure each end of Crossover Frame to each Rear Support Frame (#2) with one Bracket (#16), two M12 x 4” Carriage Bolts (#28), two . 1” Washers (#29), and two M12 Aircraft Nuts (#30). C.) Attach an Upper Pulley Bracket (#9) to the horizontal beam on the Crossover Frame (#1). Secure it with a M10 x 1” Allen Bolt (#38) and .1 .” Washer (#39). Repeat the same step to install the other side. D.) Attach the Cable (#20) to the Lower Pulley Bracket (#14). Attach a 6” Pulley (#18) to the Bracket. Secure it with one M10 x 2” Allen Bolts (#31), two . .” Washers (#32), and one M10 Aircraft Nut (#33). E.) Pull the Cable (#20) to the open bracket on the Floor Stabilizer (#6). Repeat Step D above to install a 6” Pulley (#18). F.) Pull the Cable upward towards the open pulley bracket on the Crossover Frame (#1). Install another 6” Pulley (#18). G.)Draw the Cable downward to the Small Pulley Bracket (#8) on the Weight Holder (#4). Install a 4 .” Pulley (#19) to the bracket. H.) Pull the Cable upward to the Upper Pulley Bracket (#9). Install a 6” Pulley. I.) Repeat the steps above to install the other side. J.) Attach a C-clip (#37) to the end of the Cable. Attach one end of a Chain (#36) to the C- clip and the other end to the Handle. Repeat to install the other three handles. 6 DIAGRAM 3 7 8 PARTS LIST KEY NO. DESCRIPTION Q’ty Crossover Frame 1 Support Frame 2 Base Frame 2 Weight Holder 2 Guide Rod Sleeve 4 Floor Stabilizer 2 Allen Bolt 4 Small Pulley Bracket 2 Large Upper Pulley Bracket 2 . 1” x 1 .” Brass Bushing 2 Handle 4 Guide Rod 4 Olympic Sleeve 4 Lower Pulley Bracket 2 . 1” x .” Brass Bushing 4 Bracket 4 Chin Up Grip 2 6” Pulley 8 4 .” Pulley 2 Cable 2 M10 x 1” Round Allen Bolt 8 1” Thick Rubber Bumper 8 .” Thick Rubber Bumper 4 Olympic Sleeve End Cap 4 Spring Clip 4 Spring Clip Sleeve 8 Horse Shoe End Cap 8 M12 x 4” Carriage Bolt 12 . 1” Washer 12 M12 Aircraft Nut 12 M10 x 2” Allen Bolt 10 . .” Washer 28 M10 Aircraft Nut 10 2” x 2 .” End Cap 4 Lower Pivot Bracket 4 Chain 2 C-clip 8 M10 x 1” Allen Bolt 12 . 1 .” Washer 4 Cone-shaped End Cap 2 Plastic Bushing 8 9 IRON GRIP SPORT By IMPEX FITNESS PRODUCTS LIMITED LIFE TIME WARRANTY IMPEX FITNESS PRODUCTS ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of LIFE TIME on the Frame and Weld, 3 YEARS on parts, and 6 MONTHS on upholstery from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for heavy commercial or rental purposes. No other warranty b...