Votos - , Puntuación media:
(
)
)
Fabricar: Stamina Products
Tamaño del archivo: 546.05 kb
Nombre del archivo: 4300b593-c3bd-42cf-b5c7-50598b038d0b.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES mm. in. 11/20 21/2 31/2 41/2 51/2 61/2 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 MILLIMETERS 6810 12 NOTICE: The length of all bolts and screws, except those with flat heads, is measured from below the head to the end of the bolt or screw. Flat head bolts and screws are measured from the top of the head to the end of the bolt or screw. length length After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware may be already attached to the part. Part No. and Description Qty 64 Carriage Bolt (M8 x 1.25 x 75mm) 2 65 Bolt, Button Head (M8 x 1.25 x 15mm) 9 66 Bolt, Button Head (M8 x 1.25 x 20mm) 2 67 Bolt, Button Head (M8 x 1.25 x 48mm) 2 68 Bolt, Button Head (M8 x 1.25 x 75mm) 2 72 Bolt, Hex Head (M6 x 1 x 35mm) 4 75 Screw, Round Head (M5 x 15mm) 6 81 Nylock Nut (M8 x 1.25) 2 84 Acorn Nut (M6 x 1) 4 85 Acorn Nut (M8 x 1.25) 2 86 Arc Washer (M6) 4 87 Arc Washer (M8) 13 88 Lock Washer (M6) 4 89 Lock Washer (M8) 15 45 Large Washer (M8 x o32 x 2mm thick) 2 52 Large Washer (M16 x o32 x 0.5mm thick) 2 6 7 STEP 1 Attach the FRONT STABILIZER(2) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x75mm) (64), ARC WASHERS(M8)(87), LOCK WASHERS(M8)(89), and ACORN NUTS(M8x1.25)(85). STEP 2 Attach the REAR STABILIZER(3) to the MAIN FRAME(1) with BUTTON HEAD BOLTS(M8x1.25x 75mm) (68), ARC WASHERS(M8)(87), and LOCK WASHERS(M8)(89). NOTE: You can adjust the LEVELING CAPS(61) on the REAR STABILIZER(3) to keep the Magnetic 1772 Elliptical stable. ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at: customerservice@staminaproducts.com ASSEMBLY INSTRUCTIONS 8 Bracket Cable End Spring Hook Metal Fitting STEP 3 Refer to the inset drawing. Lay the UPRIGHT(6) on the floor close to the front of the MAIN FRAME(1). Set the TENSION KNOB(25) on the UPRIGHT(6) at position 8, so the CABLE END of the TENSION KNOB KNOB(25) extends out of the metal fitting as far as possible. Connect the CABLE END of the TENSION KNOB(25) to the SPRING HOOK end of the TENSION CABLE(24). Pull the CABLE END on the TENSION KNOB(25) firmly and insert the cable through the slot in the bracket. Then insert the metal fitting on the end of the CABLE END of the TENSION KNOB(25) into the hole at the end of the slot in the BRACKET. Adjust the TENSION KNOB(25) and verify that the SPRING HOOK moves when the TENSION KNOB(25) is adjusted. STEP 4 Plug the SENSOR WIRE(30) firmly into the CONNECTION WIRE(29). CAUTION: Be careful not to damage the SENSOR WIRE(30) and CONNECTION WIRE(29) when assembling the UPRIGHT(6). STEP 5 Insert the UPRIGHT(6) onto the MAIN FRAME(1) and secure with BUTTON HEAD BOLTS(M8x1.25x15mm) (65), ARC WASHERS(M8)(87), and LOCK WASHERS(M8)(89). Do not tighten the bolts until STEP 10. ASSEMBLY INSTRUCTIONS Place the front end of the RIGHT PEDAL ARM(5) on the ROLLER(58) of the FRONT STABILIZER(2). Connect the back end of the RIGHT PEDAL ARM(5) to the RIGHT CRANK(36). Thread the RIGHT PEDAL SHAFT(42) into the RIGHT CRANK (36) and tighten securely. Repeat on the left side. STEP 7 There is an "L" decal on the LEFT PEDAL CAP(46), and an "R" decal on the RIGHT PEDAL CAP(47). Attach the RIGHT PEDAL CAP(47) to the RIGHT PEDAL ARM(5) with ROUND HEAD SCREWS (M5x15mm)(75). Repeat on the left side. NOTE: RIGHT LEFT There is an "L" decal on the LEFT PEDAL ARM(4), and an "R" decal on the RIGHT PEDAL ARM(5). The RIGHT PEDAL SHAFT(42) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL SHAFT(41) has left hand threads and is tightened by turning counterclockwise. STEP 6 NOTE: 9 The LEFT and RIGHT PEDAL CAPS(46, 47) have a raised lip on three sides. Attach the LEFT and RIGHT PEDAL CAPS(46, 47) to the LEFT and RIGHT PEDAL ARMS(4, 5) so that the side without the raised lip is on the outside. 1. 2. L R L R ASSEMBLY INSTRUCTIONS RIGHT LEFT 10 Shaft L Look down from the top R STEP 8: There is an "L" decal on the LEFT HANDLEBAR(8), and an "R" decal on the RIGHT HANDLEBAR (9). To assemble the RIGHT HANDLEBAR(9), place a SPACER(51) and a LARGE WASHER(M16)(52) on the right side of the SHAFT on the UPRIGHT(6). Slide the RIGHT HANDLEBAR(9) onto the SHAFT and secure with a LARGE WASHER(M8)(45), LOCK WASHER(M8)(89), and BUTTON HEAD BOLT (M8x1.25x20mm)(66). Repeat on the left side. STEP 9: Attach the LOWER PIVOTING ARMS(10) to the LEFT and RIGHT HANDLEBARS(8, 9) with HEX BOLTS(M6x1x35mm)(72), ARC WASHERS(M6)(86), LOCK WASHERS(M6)(88), and ACORN NUTS (M6...