Votos - 4, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Vision Fitness R2650HRT |
Resumen del manual
Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw. 1231STEP2STEP4STEP5STEP3STEP6STEP TOOLS & PARTS INCLUDED 15mm Pedal Wrench 5mm T-Shaped Wrench Screwdriver 5mm L-Shaped Wrench 4mm L-Shaped Wrench PARTS BOX Console Mast Cover Water Bottle Heart Rate Chest Strap Color-coded Hardware Bags Pedals/Straps Owner’s Guide Assembly Guide Warranty Card HARDWARE INCLUDED ORANGE BAG GREEN BAG PINK BAG BLUE BAG M8 x 15L Screw Quantity: 6 M8 x 20L Screw Quantity: 2 M8x65L Screw Quantity: 2 M8 Lock Washer Quantity: 4 M8 x 15L Screw Quantity: 2 M8 Lock Washer Quantity: 2 BLACK BAG M6 x 55L Screw Quantity: 4 M6 Lock Washer Quantity: 4 M8 x 20L Screw Quantity: 8 M8 Lock Washer Quantity: 8 YELLOW BAG M5 x 35L Screw Quantity: 2 M5 Lock Washer Quantity: 2 M10 x 12L Set Screw Quantity: 1 1STEP1STEP 2STEP Rear Foot Console Mast Console Mast Boot 1STEP• Install the rear foot with the four lock washers (M8), two inside screws (M8x65L), and two outside screws (M8x20L). Tighten with the 5mm T-Shaped wrench. ORANGE BAG 2STEP• Slide the console mast boot onto the console mast. • Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart rate wires. Pull the wire tie with wire harness and heart rate wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the console mast to the frame bracket with six screws (M8x15L). Tighten with the 5mm T-Shaped wrench. Insert a set screw (M10 x 12L) to the front edge of the mast and tighten until snug with the 5mm T-shaped wrench. • Slide the console mast boot down and snap it into place on the side cover. BLUE BAG Frame Bracket 5 Console Mast Handlebar 3STEP• Mount the upper handlebars to the console mast using two lock washers (M8) and two screws (M8x15L). Tighten with the 5mm T-Shaped wrench. • Remove the four mounting screws from the back of the console. Connect the wire harness and heart rate wires that come from the console mast into the plugs located in the back of the console. Make sure the 9-Volt battery is plugged into the console. Attach the console to the mast with the four screws removed earlier. PINK BAG 1233STEP 6 7 STEP 4 • Remove the two socket head cap screws from the sliding seat adjustment bracket. Slide the seat adjustment handle between the teeth of the seat adjustment bracket. Re-insert the two socket head cap screws and tighten with the 4mm L-shaped wrench. • Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four screws (M8x20L) and the 5mm T-Shaped wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four screws (M8x20L). Tighten with the 5mm T-Shaped wrench. GREEN BAG 123 STEP 4 Wires B Wires A Seat Handlebar Seat Frame Sliding Seat Bracket 8 STEP 5 • Mount the seat bottom to the seat frame with four screws (M6x55L) and four lock washers (M6). Tighten with the 4mm L-shaped wrench. BLACK BAG 123 STEP 5 Seat Bottom 9 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2005 Vision Fitness. All Rights Reserved. 6.05 Part #Z26RB79-AG AG18.36PRD REV1 STEP 6 • Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm Pedal Wrench. • Secure the Accessory Tray to the seat handlebar with two screws (M5x35L) and two lock washers (M5). Be careful when inserting the screws to clear the wires inside the handlebar to prevent damage. Tighten with the screwdriver. YELLOW BAG 123 STEP 6 Accessory Tray Pedal ...