Votos - 3, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Vision Fitness X6850HRT |
Resumen del manual
Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 ©2008 Vision Fitness. All Rights Reserved. 3.08 AG18.50PRD REV6 AssemblyGuide X6850HRT COMMERCIAL INCLINE ELLIPTICAL TRAINERS X6850HRT HARDWARE INCLUDED HARDWARE INCLUDED COMMERCIAL INCLINE ELLIPTICAL TRAINERS To avoid possible damage to this Elliptical Trainer, please follow assembly steps in the correct order. Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. ORANGE BAG M8x20L Socket Head Bolt Quantity: 4 8.2x18x1.5T Arc Washer Quantity: 4 HARDWARE INCLUDED BLACK BAG Plastic Connector Quantity: 4 YELLOW BAG Spacer Quantity: 4 M8x55L Socket Head Bolt Quantity: 2 8x16x1T Washer Quantity: 2 M8 Nylon Nut Quantity: 2 M5x15L Bolt Quantity: 8 M8x25L Socket Head Bolt Quantity: 8 M8 Lock Washer Quantity: 8 M8x20L Panhead Bolt Quantity: 4 PINK BAG M10x25L Socket Head Bolt Quantity: 4 M8 Lock Washer Quantity: 4 BLUE BAG M10x55L Socket Head Bolt Quantity: 2 M10 Nylon Nut Quantity: 2 M5x12L Bolt Quantity: 2 10x24.5x1T Washer Quantity: 4 Zip Tie, Quantity: 1 8x16x2T Washer Quantity: 4 M10 Lock Washer Quantity: 4 M8x25L Socket Head Bolt Quantity: 4 GREEN BAG M8x12L Bolt Quantity: 2 End Cap illustration not to scale Quantity: 226x36x2T Wave Washer Quantity: 4 26x36x0.3T Wave Washer Quantity: 2 25.5x38x1T Washer Quantity: 2 STEP 3 STEP 4 STEP 6 STEP 5 Console Mast Boot Mounting Plate Console Mast Frame Bracket Link Arm Pedal Arm Rotation Housing Dual-Action Arm Console Accessory Tray STEP 1 Front Stabilizer Tube STEP 4 • Remove protective covers from sleeves of the pedal arms. IMPORTANT: The washers in the following step must be assembled in the correct order. • Slide one thin metal wave washer (26x36x0.3T), one flat washer (25.5x38x1T), and one plastic wave washer (26x36x2T) onto the axle of the right link arm. Slide the axle of the right link arm through the sleeve on the right pedal arm. Secure the link arm onto the pedal arm with the plastic wave washer (26x36x2T), end cap, and bolt (M8x12L). Tighten with the 5mm L-shaped wrench. • Repeat the step on the left side. GREEN BAG STEP 5 NOTE: With this next step it is helpful to have a second person to hold the dual-action arms in place while you assemble them. • Take the right dual-action arm and center the holes in the rotation housing on the console mast. Secure with four socket head bolts (M8x25L) and four lock washers (M8). Tighten with the 6mm T-shaped wrench. • Attach the dual-action arm rotation cover to the dual-action arm center. Secure in place with two bolts (M5x15L). Tighten with the screwdriver. • Slide a spacer onto each side of the socket joint located on the end of the link arm. Slide the bottom of the dualaction arm bracket over the link arm socket and spacers. From the outside of the bracket, slide the bolt (M8x55L) through the hole in the bracket and socket joint. Secure with a washer (8x16x1T) and nylon nut (M8). Tighten with the 6mm T-shaped wrench and 13mm wrench. • Attach the inside dual-action arm cover onto the bottom of the dualaction arm with a bolt (M5x15L). Insert the plastic connector to the inside dual-action arm cover. Slide the outside dual-action arm cover onto the other end of the plastic connector. Secure the outside dual-action arm cover to the bottom of the dual-action arm with a bolt (M5x15L). Tighten both bolts with the screwdriver. • Repeat these steps on the left side. BLACK BAG STEP 6 • Slide the accessory tray onto the console mast. Secure in place with four panhead bolts (M8x20L). Tighten with the 5mm L-shaped wrench. • Remove the four bolts (M5x12L) from the back side of the console. Connect the data cable and the heart rate wires to the plugs in the back side of the console. Place the console on the mast and secure in place with the bolts (M5x12L). • Place the X6850HRT in its intended location and plug in the power cord to the electrical outlet. YELLOW BAG STEP 3 • Slide the console mast boot onto the console mast. • Cut the zip ties holding the cables and wires onto the console mast. • Attach the mounting plate to the bottom of the console mast with four socket head bolts (M10x25L) and four lock washers (M10). Tighten as much as possible with the 8mm L-shaped wrench. • Mount the console mast on the frame by sliding the guide hole on the mast mounting plate ov...