Votos - 4, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Vision Fitness E3800HRT |
Resumen del manual
Box 280 ♦ Lake Mills. Wl 53551 toll free 800.335.4348 ♦ phone 920.648.4090 ♦ fox 920.648.3373 ©2007 Vision Fitness. All Rights Reserved. S.07 AG10.45PRD REV3 TOOLS & PARTS INCLUDED 5mm T-Shaped Wrench Console Mast Cover Accessory Tray Color-coded Hardware Bags Owners Guide Assembly Guide Warranty Card V J HARDWARE INCLUDED ORANGE BAG M8 Lock Washer Quantity: 4 PINK BAG M8 x 151 Bolt Quantity: 4 Assembly Guide E3800HRT COMMERCIAL FITNESS BIKE To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike's serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owners Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw STEP] 1 ORANGE BAG I * Install the rear foot with four lock washers (M8), two inside bolts (M8x65L), and two outside bolts (M8x20L). Tighten with the 5mm T-shaped wrench. _y Accessory Tray * Slide the console mast boot onto the console mast. • Unfold the wire harness, coaxial cable, and TV power cable located in the console mast frame bracket. Connect the cables and wire harness to the wire tie coming from the bottom of the console mast. Pull the wire tie and cables up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the mast to the frame using six lock washers (M8) and six bolts (M8xl5L). Tighten with the 5mm T-shaped wrench. Place the seventh bolt (M8xl 5L) in the rear of the frame bracket and tighten until snug. Tighten with the 5mm L-shaped wrench. • Slide the console mast boot down and set it in place on the side cover. • Remove the nuts (M8) from the bottom of the seat. Attach the seat to the seat post with the nuts you just removed. Tighten with the 15mm wrench. V J Console in the front of the console mast. Pull these wires up through the hole at the top of the console mast. Attach the handlebar to the console mast using four bolts (M8xl 5L). Tighten with the 5mm T-shaped wrench. Heart Rale Wires * Tuck the coaxial and TV power cables into the console mast. NOTE: If you have purchased the TV bracket assembly, remove the bolts from the TV bracket cover located at the front of the console mast and remove the cover. Feed the coaxial and TV power cables through the hole at the front of the console mast. Handlebar CONSOLE * Remove the four mounting bolts from the back of the console with the screwdriver. Plug in the wire harness and the two heart rate wires to the back of the console. Attach the console to the console mast with the four bolts removed earlier in this step. * With the screwdriver, remove the Iwo bolts located half way up the console mast. Attach the accessory tray to the console mast with the two bolts. TV Bracket Wires " Console Mast Wire Harness Console Mast Boot Frame Bracket ""■3 PINK BAG * Feed the heart rate wires of the handlebar through ihe small hole located...