Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
• Slide a flat washer (M16) onto the right-hand side of the rear axle, followed by a rear wheel. • Slide the large flat washer (M8) onto the right-hand side of the rear axle, and secure with a bolt (M8 x 16MM). • Repeat above steps to install lefthand pedal arm guide rail. • X6200HRT/DA only: Slide the toepiece onto the pedal arm while simultaneously lifting the locking knob. Lock the toe-piece into place at the STEP or GLIDE position. BLUE BAG X6000DA Only STEP 3 6 STEP 3 • Mount the rear pedal arms to the front pedal arms using four bolts (M8 x 80MM) and four M8 NyLock nuts. Tighten with the 13MM wrench. • X6000DA only: Install the foot toe pieces to the front pedal arms with two bolts (M8 x 45MM) using the Blue 5MM Allen wrench. PINK BAG 7 STEP 4 • X6000DA only: Unfold the RPM sensor wire, located in the frame console mast bracket. Remove any kinks. • All models: Slide the rubber console mast cover onto the bottom of console mast, and slide it up as far as it will go. • All models: Unfold the console cable and attach it to the string located at the bottom of the console mast. Guide the wire up through the mast while simultaneously sliding the console mast onto the frame bracket. • All models: Bolt the console mast to the frame bracket with two bolts (M8 x 60MM), two flat washers (M8), and two lock washers (M8). Tighten with the Blue 5MM Allen wrench. Slide the rubber console mast cover back down over the bolt heads. X6000DA NOTE: Be sure the RPM sensor wire exits through the small slot at the top right side of the console mast. • X6000DA only: Install the batteries in the console. Mount console to console mast using the four screws. Plug the RPM sensor wire into the back of the console, and feed the excess back down into the small slot in the console mast. • X6000DA only: Turn the tension knob to Level 15. Reach inside the console mast and connect the magnet cables. Turn the knob to Level 1 and mount the knob using a bolt (M5 x 25MM). • X6200HRT/DA only: Remove the four screws from the back of the console. Plug the wire connector from inside the mast into the console. The cable connector is slotted, so it may only be connected one way; do not force it! • X6200HRT/DA only: Mount the console to the mast using the four screws. Do not pinch the cable! • All models: Bolt the water bottle cage to the console mast using the two bolts located in the mast. GREEN BAG X6200HRT/DA X6000DA X6000DA Only STEP 4 8 621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 .2001 Vision Fitness. All Rights Reserved. 4.01 Part #Z60EP08-AG1801PRD AG18.01PRD U.S. Patent No. 6,190,289 REV3 STEP 5 • Slide a large wavy washer (M26) onto the console mast axle. Locate and slide the right upper handlebar bracket onto the console mast axle and attach with a washer (M8 x 35) and M8 NyLock nut, using the 13MM wrench. Snap the plastic 13MM nut caps over the nuts. • Slide a small wavy washer (M16) onto the lower pedal arm support, followed by the right lower arm. Attach with a washer (M8 x 25) and bolt (M8 x 12MM), using the Blue 5MM Allen wrench. • Pivot the lower arm and insert the top end into the upper handlebar bracket. Attach with bolts ...
Otros modelos de este manual:Formadores - X6200HRT/DA (3.6 mb)