Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 41/ 2" MINIMUM OVERLAP, LEAVING 1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 9 12/06 ID# M682001 4. 4. Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. 4 5 6 RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. IMPORTANT! HOLE DIMPLE Bottom pole 1.5” (3.81 cm) ID STICKER Bottom pole 5” (12.7 cm) Trough Dimple Wood Scrap (not supplied) ID# M682001 12/06 10 11 12/06 ID# M682001 6. Secure tank struts (2) through center hole in pole as shown. 12 10 2 2 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT! DO NOT TIGHTEN COMPLETELY. 5. Attach pole assembly to tank (1) as shown. Secure pole assembly to tank using bolts (25) and pole mounting plate (19) as shown. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 6 19 1 25 24 24 ID# M682001 12/06 12 8. 42 6 14 16 15 IMPORTANT! DO NOT OVER TIGHTEN! 7. 2 2 18 24 24 2 2 18 IMPORTANT! DO NOT TIGHTEN COMPLETELY. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! Rotate non-secured ends of tank struts (2) to mounting holes in tank as shown. Secure non-secured ends of tank struts (2) to tank as shown. IMPORTANT! TIGHTEN ALL HARDWARE FROM STEPS 6-8 AFTER THIS ASSEMBLY IS COMPLETED. Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts (16) as shown. Tighten flange nuts (14) completely. 13 12/06 ID# M682001 Securely rest the assembly on sawhorse. Identify elevator tubes (32 and 35). 35 32 9. Toward Pole Toward Board 4 35 51 50 40 49 29 29 40 50 COMPLETED ASSEMBLY 31 32 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! TIGHTEN BOLT (29) IN LOCK NUT (31) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 10. While the system is securely resting on the sawhorse. Install elevator tubes (32 and 35) to top pole section (4) as shown. Install pole cap (38) at this time. Lower Elevator tube 32 Upper Elevator tube 35 50 38 32 31 31 50 35 ID# M682001 12/06 14 While still supported on sawhorse. Attach elevator tubes (32, 35) to backboard using spacers (30), bolts (23), and nuts (31) as shown. 30 1. Sawhorse or Support Table 9/16”, 1/2”, 3/4” 1/2” 9/16” 3/4” Extension TOOLS REQUIRED FOR THIS SECTION SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section. (2) Wrenches AND/OR (2) Socket Wrenches and Sockets 31 Phillips Screwdriver 23 15 12/06 ID# M682001 2. 45 Insert T-bolt (45) into Slam Jam bracket (44) then, attach that assembly to board using bolts (26) and nuts (14). 14 26 27 IMPORTANT! Carefully cut and peel protective film away from board prior to attaching rim. 44 44 ID# M682001 12/06 16 3. 29 31 36 35 35 WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 35 35 Support pole on sawhorse. Attach counter balance spring (36) to the spring support bracket (27) using bolt (51) and nut (31) as shown. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (36) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 51 31 36 27 17 12/06 ID# M682001 Install Slam Jam Rim to Backboard A. Fit rim (34) securely into bracket (44) as shown. Allow T-bolt (45) to slip through center hole in rim (34). B. Install reinforcement bracket (46) onto T-bolt (45) as shown. C. Install spring (47) onto T-bolt (45) as shown. D. Install special nut (48) and washer (37) onto T-bolt (45). E. Tighten nut (48) until flush with end of T-bolt (45). 4. 46 48 37 44 34 45 47 45 37 48 A B C D E 45 45 NOTE: ORIENTATION 46 OF BRACKET 5. 5. Remove packaging materials from handle assemblies (17 and 3). Remove screws on both sides of tube. 17 3 Slide upper tube (17) onto handle assembly (3). Reinsert screws removed in previous step as shown.6. NOTE: Rotate upper tube to line up screw holes. Reinsert screws removed in previous step as shown. 17 3Screws removed in step 6 ID# M682001 12/06 18 19 12/06 ID# M682001 Install handle assembly (17) to lower elevator tubes (32) using bolt (29), spacers (50), and nut (31) as shown. Secure the handle assembly (3 & 17) to pole bracket 8. (15) using bolt (20) and nut (10) as shown. Secure the front panel (21) to struts (2) as 9. shown with carriage bolts (22) and nuts (14). 17 29 31 15 42 20 10 3 14 22 21 50 50 7. Loosening the strutto- pole bolt (12) can help when aligning ...