Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Attach jack support brackets (18 & 19) to pole bracket (17) using bolts (3), washers (9) and nuts (11) as shown. ASSEMBLE THE ELEVATOR MOUNT TO A ROUND POLE 2. A. 1 2 17 33 34 18 19 Completed Assembly B. 3 17 9 3 9 11 9 9 01/07 ID# M316001 ASSEMBLE THE ELEVATOR MOUNT TO A WALL OR FLAT SURFACE 3. 17 Completed Assembly 3 19 18 9 11 B. Not Included with Hardware Not Included with Hardware Secure pole bracket (17) to flat solid surface. Install bolt heads outside for safety reasons. Attach jack support brackets (18 & 19) to pole bracket (17) using bolts (3), washers (9) and nuts (11) as shown. A. 9 ID# M316001 01/07 10 ASSEMBLE THE ELEVATOR MOUNT TO A FLAT OR ANGLED ROOF 4. A. Preassemble as shown below prior to mounting on roof. Attach struts (23), angle brackets (26 & 27) AND jack support brackets (18 & 19) to pole bracket (17) with bolts (3), washers (9) and nuts (11) as shown. 9 18 9 23 23 27 26 17 19 9 9 3 11 Hardware for these procedures are not included due to various roof and wall construction materials and design structure. NOTE: Carefully inspect mounting area for structural integrity and hidden electrical wiring. All mounting points should be sealed to prevent leaks and water damage" WARNING! A solid mounting base and/or surface, capable of withstanding normal recreational use forces, must be provided by the customer. A reliable carpenter or building contractor should be consulted if there are questions regarding this procedure. WARNING! Completed Assembly NOTE: Strut Position To U-Channel To 23 Roof 11 01/07 ID# M316001 FLAT OR ANGLED ROOF (continued) 4. Drill holes in roof. Position angled brackets and secure to roof. B. 4. C. 23 Keep assembly upright and position struts (23) on desired location on roof approx. 26”-30” (66-76 cm) apart. Level in all directions. Mark and drill holes. Secure struts in place. All mounting points should be sealed to prevent leaks and water damage" WARNING! Note position of angle brackets (26 & 27) in relation to pole bracket per style roof. To achieve 106-3/4” (2.7 m) you may have to make some adjustments such as moving angled brackets backward or adding height to the entire assembly with wood between angled brackets and roof. NOTE: Minimum distance should be 106-3/4” (2.71 m) from top elevator hole to playing surface. Homeowner must assume all responsiblilty for any personal or property damage if backboard height is lower than recommended. WARNING! USE CAUTION; ASSEMBLY IS HEAVY. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 106-3/4” (2.71 m) 27 & 26 23 Not Included with Hardware SECTION B: FROM THIS SECTION FORWARD THE ASSEMBLIES ARETHE SAME FOR SQUARE AND ROUND POLE, WALL MOUNT, AND ROOF MOUNT 12ID# M316001 01/07 1. 8 6 10 32 32 10 30 30 30 30 10 6 Attach elevator tubes (30) to the jack support brackets (18 & 19) using bolts (6), washers (10), spacers (31 & 32) and nuts (8) as shown. 31 31Completed Assembly 13 01/07 ID# M316001 7 7 9 8 7 9 8 7 7 7 9 8 7 9 8 7 Completed Assembly 16 21 24 8 10 6 10 2. 8 8 30 14 14 30 1 7 9 8 Attach height decal (28) on screw jack (24). Align lower edge of decal (28) with screw jack bottom. Place cover (21) over screw jack (24). Insert spacer (16) into screw jack assembly (24) as shown. Install screw jack assembly (24) using bolts (6 & 14), washer (10) and nut (8) as shown. 28 21 ID# M316001 01/07 14 ATTACH AN H-FRAME STYLE BACKBOARD (STYLE WILL VARY) ATTACH A COMPOSITE STYLE BACKBOARD (STYLE WILL VARY) 16 6 6 8 8 16 1. 1. BACKBOARD MOUNTING Attach backboard using hardware shown. Folow instructions that are packaged with backboard for specific assembly details. 4 13 20 20 5 2. 8 6 25 20 20 25 6 8 15 15 Attach backboard using hardware shown. Bend support brackets (20) to line up with upper holes in backboard. Folow instructions that are packaged with backboard for specific assembly details. Assemble backboard brackets (20) using bolt (5) spacer (4) and nut (13) as shown. Folow instructions that are packaged with backboard OR for specific assembly details. 15 01/07 ID# M316001 Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net. • Do not slide, climb, shake or play on base and/or pole. • When adjusting height or moving system, keep hands and fingers away from moving parts. • Do not allow children to move or adjust system. • During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net. • Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration. • Check pole system for signs of corrosion (rust, pitting, chipping) an...