Votos - 4, Puntuación media: 4.5 ( )

Fabricar: ParaBody Tamaño del archivo: 1.08 mb Nombre del archivo: 4582e757-90bb-45d6-9b65-f7f627248fb5.pdf Idioma del manual:

18. Note: The Pulley in this drawing is pre- assembled. It is shown disassembled for easy part identification. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the bracket on the Top Frame (55). Tighten the 3/8” x 2” Bolt (12) and the 3/8” Nylon Locknut (21). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 18 15 23 12 20 15 6668 50 48 67 16 17 23 21 57 15 66 23 12 21 Bracket 55 23 12 10 CABLE ASSEMBLY 19. Assembly steps 19 through 21 show how to complete the assembly of several pre- attached parts. The 5/8” x 9/16” Spacer (73) has been pre- attached on the outside of the 3 1/2” Low Pulley (92) for shipping purposes. Remove the 3/8” Nylon Locknut (21), the Spacer, and the Pulley from the 3/8” x 3 3/4” Bolt (71). Do not remove the Bolt. The Bolt has been shown removed for part identification. Reattach the 3 1/2” Low Pulley (92), with the 5/8” x 9/16” Spacer (73) between the Pulley and the Press Frame (17). Do not tighten the 3/8” Nylon Locknut (21) yet. Be sure that the 3/8” x 3 3/4” Bolt (71), the 3/8” Flat Washer (9), the 5/8” x 9/16” Spacer (73), the 3 1/2” Low Pulley, and the 3/8” Nylon Locknut (21) are oriented as shown. 20. The indicated 3/8” x 3 3/4” Bolt (71) has been inserted from the wrong side for shipping purposes. Remove the Bolt and the 3/8” Nylon Locknut (21). Slide the Cable Trap (66) and the 3 1/2” Pulley (15) onto the 3/8” x 3 3/4” Bolt (71). Re-insert the Bolt into the Front Upright (42) from the direction shown. Hand tighten the 3/8” Nylon Locknut (21) with the 3/8” Flat Washer (9) onto the Bolt. Be sure that all parts are oriented as shown. Do not tighten the Nylon Locknut yet. 21. The indicated 3/8” x 3 3/4” Bolt (71) has also been inserted from the wrong side for shipping purposes. Remove the Bolt and the 3/8” Nylon Locknut (21). Slide the Cable Trap (66) and the 3 1/2” Pulley (15) onto the 3/8” x 3 3/4” Bolt (71). Re-insert the Bolt into the Front Upright (42) from the direction shown. Hand tighten the 3/8” Nylon Locknut (21) with the 3/8” Flat Washer (9) onto the Bolt. Be sure that all parts are oriented as shown. Do not tighten the Nylon Locknut yet. 19 9 71 73 92 21 20 71 9 21 15 21 9 21 42 66 71 15 11 22. Locate the Medium Cable (58). Route the CABLE ASSEMBLY Medium Cable (58) under the 3 1/2” Low Pulley (92) attached to the lower hole in the Press Frame (17). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame and that the Cable is between the Pulley and the crossbar on the Press Frame. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (not shown). 23. Route the Medium Cable (58) around the 3 1/2” Pulley (15) attached to the lower hole in the Front Upright (42). See the inset drawing. Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (71). 24. Route the Medium Cable (58) around the 3 1/2” Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 1/2” Bolt (not shown). 25. Route the Medium Cable (58) around the 3 1/2” Pulley (15) attached to the upper hole in the Front Upright (42). See the inset drawing. Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (71). 25 22 23 24 17 Ball 92 21 71 58 21 58 21 58 Inset shows view from other side 15 4242 58 15 66 66 15 71 58 Inset shows view from other side 42 66 15 15 17 Cro...

Descargar ahora

Introduzca dos números de la imagen: